The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section shown in the figure has dimensions of b=137 mm, c=33 mm, d=66 mm, and t=7 mm. Determine: the shear stress at point H

Q: The vertical stress at point P due to the point load Q on the ground surface as shown in figure is…

A:

Q: A simply supported wide-flange beam has the cross-section and loading as shown in the figure below.…

A:

Q: 77 kN 14 kN 7 kN A B (m) 14

A: As area under shear force diagram gives change in bending moment same concept i used to get the…

Q: The stresses at a point in a bar are o1 = 29 N/mm2 (tensile) and 02= 14N/mm2 (compressive) as shown…

A:

Q: From the given figure below and its properties, calculate the stress at the top where the maximum…

A:

Q: For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from…

A:

Q: Problem 1 A simply supported wide-flange beam has the cross-section and loading as shown in the…

A:

Q: QUESTION 3: For the following steel beam, determine: a) State of stress at point A (shown on the…

A: We have to determine the value of state of stress at point A and using mohr's circle determine the…

Q: The internal shear force at a certain section of a steel beam is V=7.2kN.  The beam cross section…

A: Given:- Shear force, V=7.2 KN To find:- a Shear stress at point Hb Shear stress at point Kc Maximum…

Q: 130 32 42 32 32 3.

A:

Q: The beam of rectangular cross-section is shown in the figure below is subjected to a maximum shear…

A: Given data: Maximum shear force (S)=1900lb   FORMULA: shear stress (ζ)=S×AY¯I×bI=moment of…

Q: Q2: For the cantilever beam with uniformly distributed load shown in Figure , determine the…

A: Given data  Cross section  Length  UDL

Q: 2 KN.m 350 mm 50 mm 200 mm columna 175 mm 2 m 1 m 8 m

A: as support are simply suppourted.max BM= BMmax=wl28 =2*828 =16KNM

Q: The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius…

A: First, we draw the free body diagram:-

Q: The stresses shown in the figure act at a point in a stressed body. If σ = 5.8 ksi in the direction…

A:

Q: Two solid cylindrical rods support a load of P = 37 kN as shown in Figure below. Rod (1) has a…

A:

Q: Consider a wood beam (see figure) carrying a uniform load of 31.5 kN/m (which includes the weight of…

A:

Q: Question 10 1 2 3 A system of three bars with similar cross-section and material supports a vertical…

A:

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: The given data is: σt=20 MPaσc=80 MPaσa=2 MPa

Q: Q1: For the figure shown, if p=300N and the distance d between the force and the centroid of the…

A:

Q: ■ Example: A rectangular loading as shown below. 300 cm 100 cm 100 cm 200 cm T q=20 kPa 200 cm R U…

A: step 1-

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: Given data in question  Torque Length Diameter  Thickness  Modulus of rigidity To find out  Maximum…

Q: The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section…

A:

Q: Problem 3: Consider the figure on the right. If a point load of 5500 Ib is applied at the center of…

A: Answer:-                    This question can be solve by the help of westergard formula . In which…

Q: Consider a wood beam (see figure) carrying a uniform load of 21.5 kN/m (which includes the weight of…

A:

Q: Part B. Stress 2. Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is…

A: Consider the following free body diagram :

Q: 2. For the following stress function o to be a valid Airy stress function, what should be the…

A:

Q: Problem 3.4. A column in a two-story building is fabricated from square structural tubing having the…

A:

Q: PROBLEM 74: A hollow circular pipe 5 mm thick with outside diameter of 75 mm is subjected to a…

A: This question is based on the torsional equation. The torsional equation is as follows: Tτmax=Jr…

Q: The beam shown in Figure 5 a is subjected to an uniform load w of 2 kN/m and has a length L of 4…

A: Note :- as per our guidelines we are supposed to answer first three subparts. So please repost other…

Q: A vertical force P of magnitude 15 kN is applied at point C located on the axis of symmetry of the…

A:

Q: From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an…

A:

Q: 2.1A cantilever beam spans 8 m and carries a uniformly distributed load as shown in Figure 2. Draw…

A:

Q: z/2 r/2

A:

Q: 800 lb/ft |A B C 9,000 lb-ft 3,600 lb D 600 lb/ft X E 1 in. 5 in.

A:

Q: Problem 3.4. A column in a two-story building is fabricated from square structural tubing having the…

A: It is required to find axian stress in member AB And BC of the given column. We need to draw the…

Q: 2. For the beam shown in the figure, find (a) the maximum shear stress and (b) the shear stress at a…

A:

Q: 240 mm 120 mm 240 mm 240 mm 120 mm 240 mm Determine the magnitude of the maximum shear stress at the…

A: The moment o inertia about neutral axis for the given member is: I=BD312-4×bd312 Where, B = 600 mm D…

Q: 2) The cross-sectional dimensions of a beam are shown in Figure 2. a) Determine the centroid…

A: Given Data -

Q: If the 60 mm diameter shaft is subjected to an axial force of 10 kN, determine the average shear…

A:

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Find the equivalent force couple system at the section a-a. Then using stress equation the normal…

Q: Q1) At a point in a structure subjected to plane stress, the stresses are o= 4100 psi, Gr = 2200…

A: stress transformation means normal and shear stress are known at any plane passing through a point…

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: Length, L = 300 mm Force, F = 414 N Modulus of Elasticity, E = 2 x 105 N/mm2 Moment of…

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: Question is based on overhang beam made up of cast iron .Dimension of beam, bending and shear stress…

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

A:

Q: 01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is…

A:

Q: A cantilever beam along with its cross-section is shown in the figure below. 1) Determine the state…

A: W = 13KN/m L = 3m

Q: Two identical loads distributed over circular areas are applied on an elastic two-layer system, as…

A: Given Data:E1=150000psiE2=30000psiV=0.5r=6.5inD=16.25ing=75psih=6.5in

Q: 58 kN/m For the beam and loading shown in figure, answer the Hinge questions below -5.5 m 254 mm 18…

A: Given Structure:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.