The internal shear force V at a certain section of an aluminum beam is 12.8 kN. If the beam has the cross section shown (assume a=28 mm, bf=76 mm, tw=tf=6 mm, d=87 mm), determine: (a) the shear stress Ty at point H, which is located 28 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape.

The internal shear force V at a certain section of an aluminum beam is 12.8 kN. If the beam has the cross section shown (assume a=28 mm, bf=76 mm, tw=tf=6 mm, d=87 mm), determine: (a) the shear stress Ty at point H, which is located 28 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.10P: A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum...

See similar textbooks

Similar questions

Derive the following formula for the distance e from the centerline of the wall to the shear center S for the hat section of constant thickness shown in the figure: Also, check the formula for the special case of a channel section (a = 0).
A solid circular bar having diameter d is to be replaced by a rectangular tube having cross-sectional dimensions d × 2d to the median line of the cross section (see figure). Determine the required thickness tminof the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum allowable shear force K that may act on the beam if the allowable shear stress is 36 MPa. c
A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 7.5w N, (+)Mmax = 5.2w N-m, (-)Mmax = 4.5w N-m. From the given cross section shown, ytop = 64.183 mm, ybot = 135.817 mm, and INA = 25.059 x 10 6 mm4. The allowable stresses are as follows: σfT = 30 MPa, σfC = 60 MPa, and τ = 10 MPa. a. The safe uniform load considering tensile flexural strees is _____N/m b. The safe uniform load considering compressive flexural stress is _____ N/m. c. The moment inertia of the area about the neutral axis is _____ mm^3. d. The safe uniform load considering maximum shear force is _____ N/m e. Based on your analysis, the safe uniform load to recommend is _____ N/m.
The shear stress at the inner surface of hollow circular section is __
If a beam has a rectangular cross section of heigh 300mm and width 60mm. In one cross section plane the beam experiences a shear force of 2x10^6 N. How do I work out the; 1 - shear stress at neutral axis 2 - the bottom surface 3 - 20mm from the top surface
A simply supported beam is subjected to alinearly varying distributed load q(x) =(x/L)q0 withmaximum intensity q0 at B. The beam has a lengthL = 4 m and rectangular cross section with a widthof 200 mm and height of 300 mm. Determine themaximum permissible value for the maximum intensity,q0, if the allowable normal stresses in tension andcompression are 120 MPa.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A wood beam reinforced by an aluminumchannel section is shown in the figure. The beam hasa cross section of dimensions 150 mm × 250 mm, andthe channel has a uniform thickness of 6.5 mm. If theallowable stresses in the wood and aluminum are 8MPa and 38 MPa, respectively, and if their moduli ofelasticity are in the ratio 1 to 6, what is the maximumallowable bending moment for the beam?
A wood box beam is constructed of two 260 [mm] x 50 [mm] boards and two 260 [mm] x 25 [mm] boards (sec figure). The boards are nailed at a longitudinal spacing. b=100 [mm]. If each nail has an allowable shear force F=1200 [N], and Vmax=10652.6 [N]. What is the magnitude of the shear stress at the midpoint of either vertical plank?
A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft