The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 39⁰ KN kN m 6 KN 2.5 m 1.5 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.3 m, R= (c) The minimum value for R = i (d) The pin should be designed to hold i kN at x = kN.

The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 39⁰ KN kN m 6 KN 2.5 m 1.5 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.3 m, R= (c) The minimum value for R = i (d) The pin should be designed to hold i kN at x = kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
please i dont have much time solve fast as you can When the angle θ = 90 °, the BE hydraulic cylinder applies a vertical force (F = 3330 N) Newtons to the platform. The mass of the crate is 200 kg and the angular velocity (ω) of AB is 7 (rad / s). First, treat the box and platform as a single body to find the following: The amount of reaction forces at points B and D. Acceleration of the center of the box aG in the x and y direction. Second, after finding the previous requirements, find the following for the platform only: The force of reaction from the box to the platform (Normal force). Minimum static friction coefficient (μs) to ensure the box does not slip. Note: Neglect the weight of the platform and objects AB and CD.
Prob. 2. A 1,000-ton train is accelerated at a constant rate up a 2% grade. The train resistance is constant at 10lb/ton. The velocity increases from 20mi/h to 40mi/h in a distance of 2,000ft Question#1 From Prob. 2, determine the constant drawbar pull exerted by the locomotive
Consider the simply supported beam shown in (Figure 1). Suppose that P = 18 kN , w = 7 kN/m . Point D is located just to the left of the 18-kN concentrated load. Follow the sign convention. Part A Part complete Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at point C. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at point D. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at point D. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at…
To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=4.5a=4.5 ftft, b=6.5b=6.5 ftft, and c=10.0c=10.0 ftft. The applied forces are F1=1.40F1=1.40 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=60∘θ=60∘ with the horizontal. Neglect the weight of the beam.(Figure 1) 1. Determine the vertical reaction at A. 2. Determine the horizontal component of the pin reaction at C. 3. Determine the vertical component of the pin reaction at C.
For the dam shown in the figure , assuming the width of the dam (into the page) is 1 ft. Determine the resultant force on the side BC of the dam by the water.
Calculate the equivalent force of the distributed load and the Support Reactions (Ax, Ay and By).
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm Section and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the following A. Vertical reaction at C in kN. B. Moment reaction at C in kN-m. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
A cantilevered balcony is showing signs of distress. Until it can be repaired, we need to reduce the peak moment. The principal in charge recommends adding two rows of post shores. Our role is to determine how much that would reduce the peak moment in the balcony. a. Calculate the peak moment for a strip of balcony without added supports subjected to only its self-weight (i.e., the current situation). b. Use the Force Method to determine the reactions and draw V and M Diagrams for a strip of balcony with two rows of shores. c. Based on your results from part (b). By how much is the peak moment reduced when we add the shores?
Find the maximum moment of the given load train at point n on the beam given in the figure?(Single load and distributed load train move on the beam. (a=9 m between n-A, b=3 m between n-B)
the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees, belta=47 degrees. determine the reaction at b in kN. support A is a roller and Support B is hinge.
The 800-lb cylinder is supported by three chains as shown. Determine the force in each chain for equilibrium. Take d = 1 ft.