The lap joint is fastened with four ¾-inch diameter rivets.➢ a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets.➢ b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets.➢ c. what is the maximum value of the load P (kips) that can be applied to the joint? Problem 1:Axial loads are applied to the compound rod that iscomposed of an aluminum segment rigidly connectedbetween steel and bronze segments. P = 10 kNa. What is the stress (MPa) in the Bronze material?b. What is the stress in Aluminum in MPa?c. What is the stress in Steel in MPa?2PBronzeA=400 mm²AluminumA=600mm²4P-5 mSteelA=300mm²4 m.Problem 2:The lap joint is fastened with four 3/4-inch diameter rivets.a. If the allowable shearing stress of the rivets is 14ksi (kips per square inch), find the value of P (kips)that maybe applied to the joint. Assume that the loadis equally distributed among the rivets.➤ b. if the allowable bearing stress for the plates is 18ksi, find the value of the load P (kips) that maybeapplied to the joint. Assume that the load is equallydistributed among the rivets.> c. what is the maximum value of the load P (kips) thatcan be applied to the joint?4 in.3P1in.Problem 3:For the joint shown:a. calculate the largest bearing stress (MPa) betweenthe pin and the members.

Answered: Image /qna-images/answer/2320d3d4-523c-42cd-9a99-81e7e3104a1f.jpg

The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➤b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➤c. what is the maximum value of the load P (kips) that can be applied to the joint? 78 1 4 in. in.

The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➤b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➤c. what is the maximum value of the load P (kips) that can be applied to the joint? 78 1 4 in. in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.5P: A sign for an automobile service station is supported by two aluminum poles of hollow circular cross...

See similar textbooks

Similar questions

An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is subjected to a tensile load P = 12.5 kips that acts through the point where the mid-lines of the legs intersect (see figure part a). Determine the maximum tensile stresser, in the angle section. Recompute the maximum tensile stress if two angles are used and P is applied as shown in the figure part b.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.