Answered: The length of chain measured with a…

The length of chain measured with a chain was found to be 250 m. If the length of chain was measured with 30 m chain and the chain was 10 cm too short, the true length of the line will be

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 27P

See similar textbooks

Related questions

Q: A theodolite is set up at station A. The RL of instrument axis is 212,250 m. The angle of elevation…

Q: An open tank contains 6.5 m of water covered with 3.5 m of kerosene (Specific weight = 8 kN/m3).…

Q: ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A…

A: Given data in question Stress 17 & 10 Mpa Shear stress 26 Mpa To find out Principal stresses

Q: QUESTION: Solve for the following: Q. Horizontal component of hydrostatic pressure & its location b.…

A: Given data: A Circular gate which is 6 m below the water level making angle of opening 55° with…

Q: 1.22 Figure P1.22 shows (i) elastic-perfectly plastic and (ii) elastoplastic with strain hardening…

Q: An odd shaped body weighing 7.5 kg and occupying 0.1 cubic metre volume will be completely submerged…

A: Given. Odd body shaped body weighing=7.5 kgVolume of the body= 0.1 m3Find the specific gravity of a…

Q: The peak hour factor for a traffic during rush hour is equal to 0.60 with a highest 5-min volume of…

A: Given, Peak hour factor (PHF) = 0.60 Highest volume, q = 250 veh Space mean speed, S = 90 kph

Q: The railway wheel exerts a force on the rail and through the wooden beam, and the gravel can be…

A: Answer (a) Let us first calculate the value of maximum 'w' Consider Vertical force equilibrium for…

Q: ELL 2. From the given welded connection shown. Using A36 steel with Fy = 248 MPa and E60 electrodes…

A: Answer (1) Calculations for design thickness of plate Design thickness of the plate is given by the…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Answer Given data: Normal stress in x- direction σx = 30 Mpa Normal stress in y-vertical direction…

Q: A proposed office building will include a 10 ft x10 ft square, 3 ft deep (the footing height is also…

A: Given, Cross sectional area of footing = 10 ft x 10 ft Depth of footing = 3 ft Angle of internal…

Q: Use A992 steel and select a W12 shape for axially loaded column as shown below to meet the…

A: Given:- Steel grade used = A992 The length of the member = 23 ft Both ends are pinned The bracing…

Q: Question 8 A three hinged arch is 6 m high and 18 m long. The supports are at same level. Arch is…

A: Given- Height h=6 mLength L=18 mLoading as shown in the figure It is needed to find the ratio of…

Q: ation 1: A concrete column, 330 x 330 mm supports an axial compressive load of 1100 kN. Determine…

Q: What is the specific weigth and density of water?

A: What is the specific weigth and density of water?

Q: 2 ft 12 ft 8 ft. B W

Q: A gravity rapid sand filter with an effective size of 0.55 ent is 1.2 designed for a water treatment…

A: The given data in the question is: The gravity rapid sand filter has an effective size of 0.55 mm…

Q: Car A is traveling at the constant speed of 68 km/h as it rounds the circular curve of radius r =…

Q: Gage Reading 3000 N/m² psi Local Atmospheric Pressure 14.7 psi kPa Fluid Absolute Pressure 14,400…

Q: Find power required in the UNIT OF WATT

A: Given data. Density of water,ρ=1000 kg/m3ambient temperature flows through a horizontal pipe…

Q: A pollutant entered into a confined aquifer of 5 m thick and porosity 25%. If the seepage discharge…

A: Given Data Thickness of aquifer (H) = 5m Porosity (n) = 25% = 0.25 Seepage discharge (qs) = 0.25…

Q: Solve the problem of centroid of solids and find x-bar, y-bar and z-bar.

A: Answer Calculation of x We know from centroid formula x = V1*x1-V2*x2+V3*x3V1-V2+V3 V1 = Volume of…

Q: The bottom of a river is 33 ft. below the water surface, Underneath the bottom of the river is a…

A: Given Depth of river = 33 ft Specific gravity of silt = 1.25 Pressure = 90 lb. per sq. in. To find…

Q: For an embankment dam, the longest fetch is equal to 10 km, and is normal to dam axis. Assume that…

A: Given upstream slope of dam = 3H:1V average reservoir depth D =25m the longest fetch = 10 km To find…

Q: Calculate the internal axial force in member AB, BE, BF and BC and state whether it is in tension or…

A: As there are multiple questions posted, according to the guidelines, only the first three are being…

Q: What is equivalent dumping in the basic concept of vibrating system?

A: Equivalent damping in the basic concept of vibrating systems refers to the total damping in a system…

Q: A Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1…

Q: 2-67. The two forces F₁ and F₂ have a resultant force of FR = {-100k} lb. Determine the magnitude…

A: Given data: The first force, F1=60 lb The resultant force, FR= -100 k lb

Q: At a hydro electric power plant site, available head and flow rate are 24.5 m and 10.1 m³/s…

A: Given Head = 24.5 m Flow rate=10.1 m3/s efficiency η=90% To find Type of turbine

Q: A laboratory has installed a double-suction, three-stage, centrifugal pump with a discharge of 330…

Q: ETERMINE THE ABSOLUTE PRESSURE OF A IF THE AIR PRESSURE IS 2KG/CM3

A: The pressure force is defined as the force that is exerted by the pressure on any area that is equal…

Q: The strength of a sample of fully matured concrete is found to be 50 MPa. Find the strength of…

Q: List only Two of the following: 1) The Purpose of Water Demand with the percentage of each purpose.…

A: This question is related to the Environmental Engineering from Civil Engineering. As per question we…

Q: Question A concrete beam of rectangular cross-section of 200 mm x 400 mm is prestressed with a force…

A: Given Cross-section- 200 mm × 400 mm,Force P=400 kN,e=100mm. It is needed to find the maximum…

Q: A sample of 500 g dry, when poured into a 2 litre capacity cylinder which is partially filled with…

A: Given that :- Weight of dry sand = 500 gm Water displaced by sand = 188 cm3 Volume of the sand = 188…

Q: hinge A hinge hinge (e) -hinge DE CASTE CAPACITA (b) hinge -fixed base (d) PENGERS HOMEPA

Q: A rectangular watertight box is 600 mm long, 400 mm wide and 200 mm deep. It weighs 220N. If it…

A: Given, Length = 600 mm or 0.6 m Width = 400 mm or 0.4 m Depth = 200 mm or 0.2 m Weight (W) = 220…

Q: 7. Determine the effective net area of the 12.5 mm thick plate shown below using the NSCP 2015…

A: Given Plate thickness = 12.5 mm Diameter of bolts = 20 mm To find The effective net area

Q: A pollutant entered into a confined aquifer of 5 m thick and porosity 25%. If the seepage discharge…

Q: 14. Find the elevation of point A in the figure shown. 30 cm Hg DAIR Vacuum Gasoline (5=1₁5) Ale B…

A: Given To find The elevation at point A

Q: A cantilever beam of clear span 2 m is built into a wall of 30 cm thickness. The beam carries a…

Q: Eight kilometers below the surface of the ocean the pressure is 81.4 MPa. Determine the density of…

A: Given- Depth h=8 km=8000 m Pressure P=81.4 MPa, B=2.87 GPa It is needed to find the density of sea…

Q: In a one-lane road V=1800veh/h. what is the probability that a vehicle will arrive in the next five…

A: Given: Vehicle arrival rate = 1800veh/h Required: Probability of a vehicle arriving in next five…

Q: 9. Find the moment of inertia of the object shown below. The shape is symmetrical from top to…

A: Objective: To determine the moment of inertia of the given object. Given: Length (Ly) = 5.0 m…

Q: Determine the pressure difference between points A and B in kPa. Given Specific Gravities: Benzene…

Q: True or False: "Shields" are very old rocks that make up the granitic core of the continents. True…

Q: C A trickling filter plant treats 1500 cum per day of sewage with a BOD, of 220 mg/L and a suspended…

Q: ) Calculate the dry weight feed rate, ash production rate, heat value of the dry volatile fraction…

A: Given, Wet feed rate of Municipal Solid waste (MSW) = 93000 lb/hr Heat value = 5200 BTU/lb Moisture…

Q: , Conduct a mass balance to determine the amount of (a) ash, (b) water and (c) dry exhaust produced…

A: Given, Waste supply rate = 5000 tons/day Moisture content (w) = 30% Ash content = 15% NOTE : As…

Q: (D) 10. Determine the LRFD design tensile strength and the ASD allowable design tensile strength for…

A: Given: Section: W 250 x 67 bolt diameter, d = 16 mm A572 grade 50 steel: fy = 345 MPa fu = 448 MPa…

Question

The length of chain measured with a chain was found to be 250 m. If the length
of chain was measured with 30 m chain and the chain was 10 cm too short, the
true length of the line will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the actual length of a 20 m chain is found to be19.8 m, then the actual length of a line measured as 100 m with that chain will be.
A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to be 1500m. The tape was Standardized under a pull of 6.75kg but after the line was measured, it was Found that the pull actually used during the measurement was = 7.75 kg. what Was the true length of the line if the tape was standardized & used on the flat? Take young modulus, E = 2,000,000 kg/cm²
A distance of 1300 m was measured by a 40 m chain. Later on, it was detected that the chain was 0.1 m too long. Another 400 m was measured and it was detected that the chain was 0.15 m too long. Determine the exact length (m) that was measured. Express your answer in 3 decimal places.
SHOW COMPLETE ILLUSTRATION & SOLUTION A line 50m long was paced by a civil engineer three times and recorded the following results, 58, 60 and 61. He also paced another line three times and obtained the following results: 231, 236 and 227. Determine the length of the line.
Answer the following problem. Show complete solution and illustration. Two parallel sides of a rectangle are being lengthened at the rate of 20 mm/sec, while the other two sides are shortened in such a way that the figure remains a rectangle with a constant area of 5000 sq mm. What is the rate of change of the perimeter P when the length of the increasing side is 50 mm?
A line of true length 398 m when measured by a chain of 20 m chain is recorded to be 400 m. What is the actual length of the chain (in m)?
Determine the centroid of the area shown in the figure in reference with the X and Y axes. (bar x, bar y) Select the correct answer: 0.517,0.04 0.04, 0.571 0.571,-0.571 -0.571,0.571
A 100 meter tape weighing 5.08 kilograms was used to measure a line. It was supported at the end points and on its midpoint having a 60 newton applied tension. If the total measured distance is 2345.76 meters, what is the correct distance of the line?
A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water to fall from 2.0m to 1.0m. Take Cd=0.60. include your free body diagram a. 2582 seconds b. 1814 seconds c. 3600 seconds d. 3179 seconds
A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water to fall from 2.0m to 1.0m. Take Cd=0.60. a.3179 seconds b.2582 seconds c.1814 seconds d.3600 seconds
Investigate the diameter of the electrical wire used in your home. How thick are theinterstate transmission lines,and what is their cross-sectional area
A distance of 1500 m was measured with a 20 m chain. After the measurement chain was found to be 80 mm longer. If the length of chain was perfectly correct while starting measurement, what is the true length of the line measured? Solution: Average correction per chain length