The lower lumbar region A of the spine is the part of the spinal column most susceptible to abuse while resisting excessive bending caused by the moment about A of a force F. For given values of F, b, and h, determine the angle O which causes the most severe bending strain. Find a general solution and then evaluate your answer if h = 9.0 in., and b=15.5 in. Answer: 0-

The lower lumbar region A of the spine is the part of the spinal column most susceptible to abuse while resisting excessive bending caused by the moment about A of a force F. For given values of F, b, and h, determine the angle O which causes the most severe bending strain. Find a general solution and then evaluate your answer if h = 9.0 in., and b=15.5 in. Answer: 0-

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter18: Mathematics In Engineering

Section: Chapter Questions

Problem 21P

See similar textbooks

Similar questions

The reinforced concrete beam shown is simply supported at A and B. The modulus of flexural rigidity of the beam from the midspan towards A is double that of from the midspan towards B (as indicated in the figure). Wherein the moment of inertia from the midspan to point B is 980x10^6 mm^4. Using the Conjugate Beam Method, calculate the Rotation in degrees of the Beam at 3 meters from support A E = 50 GPa
If theta = 45 degrees, and T = 4 kN, determine the magnitude of the resultant force acting on the eyebolt and its direction measured clockwise from the positive x-axis. Please see the figure in the following picture.
As shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main body weighs 25 kg, while the upper rectangular portion weighs 3 kg. Assume the coefficients of friction between the cabinet and the floor are μs = 0.33 and μk = 0.28. Knowing that the force P exerted by the man's shoulder on the horizontal cabinet: 1.1 Find the required leaning force P that the man needs to exert to the cabinet for sliding to impend (assuming without tipping) 1.2 Find required leaning force P that Joey needs to exert to the cabinet for tipping to impend (assuming without sliding) 1.3 If the man's horizontal leaning force is 90 N, which of the following best describes the motion of the cabinet? (Moving, At Rest, Tipping, Sliding, Impending to Slide, Impending to Tip etc.)
Use Moment Distribution Method determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 141.9 kn.m MBC= -141.9 kn.m MCB= 81.26 kn.m
The reinforced concrete beam shown is simply supported at A and B. The modulus of flexural rigidity of the beam from the midspan towards A is double that of from the midspan towards B (as indicated in the figure). Wherein the moment of inertia from the midspan to point B is 980x10^6 mm^4. Using the Conjugate Beam Method, calculate the Rotation in degrees of the Beam at 3 meters from support A
Determine the moment of inertia for the rectangular area shown with respect to (a) the centroidal x' axis, (b) the axis xb passing through the base of the rectangle, and (c) the pole or z ' axis perpendicular to the x'-y' plane and passing through the centroid C.
For the figure shown knowing that a = 1.00 cm and b = 4.00 cm, determine:a) The centroid of the figure shownb) The moments of inertia Ix and Iy and the product of inertia Ixy around the x and y axes.c) The angle θm corresponding to the location of the main axes.d) For the u-v axes shown and obtained by rotating an angle θ= 34.0 ° clockwise, the corresponding moments and product of inertia using Mohr's circle.
Determine the moment of inertia (in mm4) of the given figure with respect to x axis. Assume y=95 mm and z=59 mm. Round off only on the final answer expressed in whole number.
Determine the moments of inertia bar-Ix of the area shown with respect to centroidal axis parallel to side AB Where: a=2.4 in b= 1.7 in c= 1.8 in
in the system shown, determine the value of the force f if the coefficient of friction between the body and floor is 0.41. P is 264.87N
A tennis player strikes the tennis ball with her racket while the ball is still rising. The ball speed before impact with the racket is v1 = 15 m/s and after impact its speed is v2 = 20 m/s, with directions as shown in the figure. If the 60-g ball is in contact with the racket for 0.047 s, determine the magnitude of the average force R exerted by the racket on the ball. Find the angle β made by R with the horizontal. Comment on the treatment of the ball weight during impact.
2. The cross section of a rectangular hollow beam is as shown in figure. Determine polar moment of inertia of the section about centroidal axes. [Izz= 1,54,45334 mm4]