The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline. B 30- 20° 16

The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline. B 30- 20° 16

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A (on the ground.) The angle friction at all contact surfaces is 21.8°. Fiind the smallest angle at which ladder can be inclined with the horizontal before it is on its verge of slipping.
Topic: Fluid mechanics Problem: A rectangular scow 9m wide, 15m long, and 3.6m high has a draft in seawater 2.4m. G is located 2.7m above the bottom of the scow. Determine the following: a) The initial metacentric height b) The righting or overturning moment when the scow tilts until one side is just at the point of submergence.
Q: The ball was thrown with a speed (v, = 35 m/sec) and directed at an angle (8,4 = 30°)with the horizontal. Determine the distance R where the ball hits the slope at B.
A tacheometer fitted with an anallatic lens was used to observe the following:InstrumentStation W.C.B Staff Station VerticalAngle Staff Readings(m) C 320 0 A -12 0 0.906, 1.728, 2.550C 50 0 B + 10 0 0.744, 2.199, 3.654The value of the constant was 653and the staff was held vertically. Determine thelength R.L of A & B and gradient of AB
The horizontal barshown (Length = 15.0 feet) rests on smooth inclines. Compute the distance x at which load T= 250 lbs should be placed from point B to keep the bar horizontal?
A wooden cylinder (sg=0.61) is placedvertically in oil with specifc gravity of 0.85. Determine the metacentric height.
Using Area-Moment Method, determine the deflection at the overhanging end in mm. Given: P = 4.2kN , w = 8.6 kN/m , a = 1.6m , b = 1.2m , c = 0.7m , E = 10 GPa , I = 20x106 mm4
A Block weighing 100N is held on a 400 incline by a Bar attached to a 150N Block on a horizontal plane. The Bar which is fastened by a smooth pin at each end is inclined 200 above the horizontal. The angle of Friction between each Block and its Plane is 180. Find the horizontal Force P applied to the150N Block which will cause it to be on the point of moving to the right?
A bar slides on a vertical post and is attached to a block A that is moving to the right with a constantvelocity C as shown. Determine the angular velocity, ω of the bar as a function of C, a, and θ.
Data are as follows: P=6.2 kN, L=3.2m, d=1.25m, b=80mm, t=25, h=120mm, h1=90mm. Determine the moment of inertia about the centroidal x-axis in mm^4.
The two blocks (MA = 100 kg, MB = 150 kg) shown are originally at rest. Assuming that the coefficients of friction between the blocks and the inclines are ms = 0.25 and mk = 0.20, determine a. acceleration of block A b. tension in the cord