The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A, three members, and a riveter which is attached to the slider block D Figure 150 mm T 45° 45° 60 200 mm 300 mm 30 VA < 1 of 1 > Part A Determine the velocity of D at the instant shown, when the piston at A is traveling at v₁ = 22 m/s. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. vp= Submit 4 Value Provide Feedback 1 Request Answer → C Units ? Next >

The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A, three members, and a riveter which is attached to the slider block D Figure 150 mm T 45° 45° 60 200 mm 300 mm 30 VA < 1 of 1 > Part A Determine the velocity of D at the instant shown, when the piston at A is traveling at v₁ = 22 m/s. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. vp= Submit 4 Value Provide Feedback 1 Request Answer → C Units ? Next >

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rod by which slider A is attached is rotating along a horizontal plane. Its position is defined by θ = 1 /2 sin(π t) where theta and t are expressed in radians and seconds, respectively. The slider A slides along the rod so that its distance r=1+e ^2t, where r is expressed in centimeters. When t = 3 s, determine the magnitude of the velocity of the collar.
Should the moment at ED be 256.95? and i am not seeing you calculate that moment at E
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
The 42 foot long overhanging beam shown is supported by a pin at A and a roller at C. The beam supports a point load of 42 kips at point B. Determine the slope at pin A, deflection at point B, and the slope and deflection at point D. Modulus of Elasticity, E = 10,000ksi, Moment of Inertia, I = 2500in4. Let slope and deflection be functions of x, with x positive to the right.
Q2) In the figure shown, find the direction from point M into point P, if you know the direction the line LP = 40° 15° v, Wt / %,
The position of the slider P in the rotating slotted arm OA is controlled by a power screw as shown. At the instant represented, θ˙ = 5.4 rad/s and θ¨ = -35 rad/s2. Also at this same instant, r = 396 mm, r˙ = -251 mm/s, and r¨ = 0. For this instant determine the r- and θ-components of the acceleration of P.
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
For the figure shown knowing that a = 1.00 cm and b = 4.00 cm, determine:a) The centroid of the figure shownb) The moments of inertia Ix and Iy and the product of inertia Ixy around the x and y axes.c) The angle θm corresponding to the location of the main axes.d) For the u-v axes shown and obtained by rotating an angle θ= 34.0 ° clockwise, the corresponding moments and product of inertia using Mohr's circle.
Data are as follows: P=6.2 kN, L=3.2m, d=1.25m, b=80mm, t=25, h=120mm, h1=90mm. Determine the moment of inertia about the centroidal x-axis in mm^4.
In the frame shown what is the value of the vertical reaction force component at C? a. 557.4 N (Down) b. 1000 N (Down) c. 557.4 N (Up) d. 1000 N (Up)
Two children are playing in the park on a seesaw mounted on a merry-go-round as shown in the figure below. The merry-go-round rotates about the ground-fixed (frame GG) vertical at \omega_{v}=ωv= 2.9 rad/sec, and at the instant shown the seesaw turns at \omega_{H}=ωH= 2.5 rad/sec relative to the merry-go-around JJ. \left(\hat{i},\hat{j},\hat{k}\right)(i^,j^,k^) are unit vectors fixed in the seesaw board BB. The children are each 5 ft from the fulcrum OO. The girl slides a stone PP along the see-saw board toward the boy. The velocity of the stone relative to the board is -4.4 \hat{j}j^ ft/sec at an instant when the stone is 2.3 ft from the girl and \theta=0 \degθ=0deg. Find the magnitude of the velocity of the stone PP relative to the ground GG, i.e., V_{P/G}VP/G, at this instant.
Solve in 30 min I will upvote you