A uniform thin disk of mass 1 kg and radius 0.1 m is kept on a surface as shown in the figure. Aspring of stiffness k1400 N/m is connected to the disk center A and another spring of stiffnessk2= 100 N/m is connected at point B just above point A on the circumference of the disk.Initially, both the springs are unstretched. Assume pure rolling of the disk. For small disturbancefrom the equilibrium, the natural frequency of vibration of the system isoff to one decimal place).rad/s (roundk2k1y

Given data; consider the point at which the circles touches bottom as O; Using the energy…

Answered: the natural frequency of vibration of…

Engineering

Mechanical Engineering

the natural frequency of vibration of the system is rad/s (round ce)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.12P: A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic...

See similar textbooks

Similar questions

The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
Solve the preceding problem if the collar has mass M = 80 kg, the height h = 0.5 m, the length L = 3.0 m, the cross-sectional area A = 350mm2. and the modulus of elasticity E = 170 GPa.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
A heavy flywheel rotating at n revolutions per minute is rigidly attached to the end of a shaft of diameter d (see figure). If the bearing at A suddenly freezes, what will be the maximum angle of twist <£of the shaft? What is the corresponding maximum shear stress in the shaft? (Let L = length of the shaft, G = shear modulus of elasticity, and / = mass moment of inertia of the flywheel about the axis of the shaft. Also, disregard friction in the bearings at Sand Cand disregard the mass of the shaft.) Hint: Equate the kinetic energy of the rotating flywheel to the strain energy of the shaft.
A bumper for a mine car is constructed with a spring of stiffness k = 1120 lb/in. (see figure). If a car weighing 3450 lb is traveling at velocity v = 7 mph when it strikes the spring, what is the maximum shortening of the spring?
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
A flywheel of mass 120 kg and radius of gyration 450 mm is rotating at 760 r.p.m. It is brought to rest by means of block brake system as shown in the figure. The mass of the brake drum assembly is 5 kg. The brake drum is made of cast iron having specific heat 470 J / kg°C. and the brake system provides a braking torque of 380 N-m. If the diameter of brake drum is 300 mm, the coefficient of friction is 0.35. find 1. The force (P) to be applied at the end of the lever for the clockwise rotation of drum. 2. Assuming that the total heat generated is absorbed by the brake drum only, calculate the temperature rise
Under some circumstances, when two parallel springswith constants k1 and k2 support a single mass, theeffective spring constant of the system is given byk 4k1k2/(k1 + k2). A mass weighing 20 pounds stretchesone spring 6 inches and another spring 2 inches. Thesprings are first attached to a common rigid supportand then to a metal plate. As the figure illustrates(see image), the mass is attached to the center of the plate in the distributiondouble spring. Determine the constant of theeffective spring for this system. find the equationof motion if the mass is initially released fromequilibrium position with downward speed of2 ft/sec.