The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take o_all=243ksi for pin material.

The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take o_all=243ksi for pin material.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.1P: An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The...

See similar textbooks

Related questions

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A: Given data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: The one end of a hollow square bar whose side is 10.35 in with 1.35 in thickness is under a tensile…

Q: Problem 7 A 12-inches square steel bearing plate lies betw een an 8-inches diam eterw ooden postand…

Q: The one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Cross section of the bar,Hollow square tube, a=10.47 inchthickness, t=1.47 inchtensile stress on…

Q: An axially square tied column; given Pu= 4000 kN, fy = 420 MPa and fe= 28 MPa. If it is to be…

A: Given: For an axially square tied column, Pu=4000 kN, fy=420 MPa, f'c=28 MPa, ρg=0.025.

Q: H.W: 1 rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: The one end of a hollow square bar whose side is (10.50) in with (1.50) in thickness is under a…

A: Given data: The side of the square bar is a=10.5 in The thickness of the bar is t=1.5 in The tensile…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

A: Given, σy-B = 60 MPaσy-CD = 100 MPaSF = 2t = 6 mm Consider below FBD for the given question:

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness…

A: Given data for aluminum cylinder 2014-T4

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Data given- N= 47 So Side of sqaure x = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in…

Q: The one end of a hollow square bar whose side is 10 in with 2 in thickness is under a tensile stress…

A: Given Data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: The lap joint shown in Fig. P-126 is fastened by four 4-in.-diameter rivets. Calculate the maximum…

Q: The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: The one end of a hollow square bar whose side is 10.17 in with 1.17 in thickness is under a tensile…

A: Calculate the area of the hollow square bar.

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Solution: The square section is shown below, Outer side length…

Q: The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile…

Q: Design the yoke and rod connection as shown on the figure to withstand a load of 14 KN. If the…

Q: The one end of a hollow square tube whose side is 10 in with 1 in thickness is under a tensile…

A: Given dataSide length of the hallow square pipe a = 10inThickness of the hallow square tube t =…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Given Data: The side of the hollow square bar is s =10.47 in. The thickness of the bar is t = 1.47…

Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…

A: Given: The torque transmitted by shaft, T = 850 lb.in The shaft diameter, d = 1.75 in The ultimate…

Q: The one end of a hollow square bar whose side is 10.69 in with 1.69 in thickness is under a tensile…

Q: Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: igure below are cables ( circular section) supporting a MN kN. Find the axial stress of each. The es…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A: Given Data The length of the side is: a=10 in The thickness is: t=1 in Cross sectional area is…

Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…

A: Given: The maximum torque is 850 in-lb. The diameter of the shaft is 1.75 in. Ultimate stress is…

Q: The simplest truss consists of two rods and is loaded by a force. Given: F=13KN, angle a=44°. Cross…

A: Given:F=13 KNα=44°N=1.9σy=390 MPa

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: A 100N load is added to the end of circular cross section steel rod that has a length of 0.3m and a…

A: GIVEN DATA- Length of bar L=0.3m Diameter of bar d=0.025m Load P=100N Young Modulus…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. P-211. Axial loads…

A: Given that: For the composite bar maximum allowable horizontal deformation is 3 mm. It is required…

Q: A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside…

A: Inside diameterdi=100 mm di=0.1 m Outside diameter=do Tensile loadP=500…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: 2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset…

Q: Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure.…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…

Q: 1.7 The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given, Diameter of wooden post = d = 8 in Length of square concrete footing = L = 12 in Working…

Q: Steel bar with dimensions with (10mm and 10mm) subjected to axial load of * 2000N. Determine the…

Q: The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?