The op amp in the circuit in (Figure 1) is ideal. Take R = 80 ΚΩ Figure 6 kQ www 120 mV la 20 kQ ww ●+ ●9 V •-9 V 240 ΚΩ + Va 60 kn 10 1 of 1 + vo {R ▼ ▼ ► ▸ Part A Calculate ia- Express your answer to three significant figures and include the appropriate units. ia = Submit Part B Va = Submit Part C O Part D μÀ Value Calculate Va- Express your answer to three significant figures and include the appropriate units. Request Answer _ Ti μA Value Units Request Answer ? Units ?

The op amp in the circuit in (Figure 1) is ideal. Take R = 80 ΚΩ Figure 6 kQ www 120 mV la 20 kQ ww ●+ ●9 V •-9 V 240 ΚΩ + Va 60 kn 10 1 of 1 + vo {R ▼ ▼ ► ▸ Part A Calculate ia- Express your answer to three significant figures and include the appropriate units. ia = Submit Part B Va = Submit Part C O Part D μÀ Value Calculate Va- Express your answer to three significant figures and include the appropriate units. Request Answer _ Ti μA Value Units Request Answer ? Units ?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Similar questions

Please show working out and answer for the below question. You are investigating the electrical testing circuits and find that, in an inductive circuit, the relationship between instantaneous current i (amps) and the time t (secs) is given by: i = 12.5(1-e-t/CR) Determine the time taken for current to rise from 0 to 1.9 amps with resistor value of 220 and capactor value of 0.000008
These are questions related operational amplifier. Please Solve all three sub-parts..Thank you
Evaluate the multiplication factor required to extend the range of amoving coil ammeter to measure current I, if the full scaledeflection current is Im.A moving coil ammeter has a coil resistance of 1.5kΩ and needs apotential difference of 1V for full scale deflection. Calculate thevalue of shunt resistance required to extend its range to measure80 A
Please answer as quickly as possible, I'll give upvote. Thank you very much. The circuit has been running for a long time prior to the switch closing at t = 0. The supply voltage is 100(√2)sin(100t) V. The complete response of the iL(t) is of the form: iL(t) = A1e(-A2t) + B1sin(100t+B2) Amp where A1, A2, B1 and B2 are unknown. Find the instantaneous value of iL at the moment of switching (t=0).
The op amp circuit shown is ideal. The values for the circuit are as follows:+VCC = 12.0V, -VCC = -10.0V, Ra = 9.00Ω, Rb = 30.0Ω, Rc = 42.0Ω, Rd = 4.00Ω, Re = 32.0Ω. Write a KCL equation at node n. Solve for the output voltage vout as a function of the inputs va and vb. If input va=2.00V and output vout =10.0V, then solve for input vb. If inputs va=8.00V and vb=5.00V, then solve for the power absorbed by Rb. If input va=4.00V, then solve for the range of input vb such that the amplifier does not saturate.
What factor(s) can contribute to differences betweentheoretical (ideal) values in a circuit, and values measured inactual practice?a. Component tolerances onlyb. The sequence that components are placed in a circuitc. Measurement inaccuracy onlyd. None of the choices givene. Both component tolerances and measurement inaccuracy
You are investigating the electrical testing circuits and find that, in an inductive circuit, the relationship between instantaneous current i (amps) and the time t (secs) is given by: i = 2.1(1-e-9t) You have been asked to determine the time taken for the current to rise from 1 to 1.5 amps. Comment on the time taken for the current to rise the same increment from 1.5 to 2 amps and give reasons.
Design the following conditions using an operational amplifier: Cadmium sulfide (CdS) is commonly used to fabricate resistors whose value depends on the intensity of light shining on its surface. In Figure 1, a CdS “photocell” is used as the feedback resistor Rf. In total darkness, it has a resistance of 100kΩ and a resistance of 10kΩ under a light intensity of 6 candela. RL represents a circuit that is activated when a voltage of 1.5V or less is applied to its terminals. Choose R1 and VS so that the circuit represented by RL is activated by a light of 2 candela or brighter.
You were tasked with modifying an audio amplifier circuit. Amplifier circuits are responsible for increasing the current sent to the speakers, avoiding damaging the sound device. The original design is shown in the figure. You want to increase the current I1 by a factor of 10 (10 times). The conditions of the design area are: Both font values must be increased. None of the values can be equal to 0. What are the new values that you propose for the design of the amplifier? ** Argue your answer by analyzing the results obtained through calculations. (Check image 4 for the circuit)
Design an amplifier circuit using OPAMP with vo= (5*v1)+(v2)+(3*v3)-(2*v4). Draw vo knowing that v1 = 1 sin (1000*pi*t), v2 = 2 sin (2000*pi*t), v3 = 3sin (3000*pi*t), v4 = 4 sin (4000*pi*t)
subject: Communication Fundamentals Modulation and Demodulation (give solve sub-parts iv and v)
"determine Vo and Id" Please help me solve the following electronics exercise