The opne-top and completely full cylindirical tank is rotated with a constant angulat velocity o=33.5 rad/s. Calculate volume of water which will be kept in the tank after the rotation. Calculate the depth of water when the tank stops after rotation. Hint: A parabolic water surface is observed during rotation, and volume under the paraboloid is equal to one third of a cylinder with the same height. 1,0 m Zo ū 0 (0) 0, 25 m 0,50 m M Wo=0

The opne-top and completely full cylindirical tank is rotated with a constant angulat velocity o=33.5 rad/s. Calculate volume of water which will be kept in the tank after the rotation. Calculate the depth of water when the tank stops after rotation. Hint: A parabolic water surface is observed during rotation, and volume under the paraboloid is equal to one third of a cylinder with the same height. 1,0 m Zo ū 0 (0) 0, 25 m 0,50 m M Wo=0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tank has one of its side inclined inward at an angle of 30° with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having it's vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev 14.00 m, find the actual velocity of the jet air friction. Neglect air friction. Include fbd.
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 30 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m.
Estimate the height which water will rise in a capillary tube 12mm diameter. Use surface tension = 0.0728 N/m and gamma = 9810 N/m^3 Ans. No Capillary Action
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
A centrifugal pump which runs at 104.3 rad ·s−1 (16.6 rev/s) is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre. For a flow rate of Q (m3 ·s−1) the friction loss in the suction pipe is 68Q2 m and that in the delivery pipe is 650Q2 m. The impeller of the pump is 350 mm diameter and the width of the blade passages at outlet is 18 mm. The blades themselves occupy 5% of the circumference and are backward-facing at 35◦ to the tangent. At inlet the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and other losses in the pump, the velocity heads in the suction and delivery pipes, and whirl slip are all negligible, calculate the rate of flow in liter/s and the manometric efficiency of the pump.
A cylindrical buoy 100mm in diameter and120mm high is placed vertically inside thetank. The tank is 150mm in diameter andcontains water 200mm deep and oil 30mmdeep. If the buoy weighs 5N, determine thedepth of the buoy submerged.
A pump draws water from a 20 cm diam suction pipe and discharges through a15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPaat A in the suction pipe. The 15 cm diam pipe discharges horizontally into air atC. To what height h above B can the water be raised if B is 1.8 m. above A and20 hp is delivered to the pump? Assume that the pump operates at 80 %efficiency and that the frictional loss in the pipe between A and C is 3 m. Determine the inclination angle at point C for the water stream to reach a range of 50 m. Also, calculate the maximum height that the water can go from the selected datum plane.
An open cylindrical vessel 1.20m in diameter and 2.10m high is 2/3 full of water. If the vessel is rotated about its vertical axis at a constant speed of 90rpm, compute:The height of the paraboloid the water at a constant speed of 90rpm rotation.
A reservoir contains water has a vertical circular orifice 25.2mm diameter and is first plugged up to measure any displacing force, the tank is suspended in a particular way. The horizontal force is required to keep the tank in place on the removal of the plug. The opposite applied force to the orifice is 16.8N. The volume per time was found as 141lt/minute. It is assumed that the level of the water is maintained at a constant height of 2.785m above the orifice. Calculate Cc, Cv, and Cd for the orifice.
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
3. Attached photo for the problem Sharp edge orifice... (my answer was -2.43) 4. A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev = 20m) into open air (Point 3 elev. 10m). The head loss from the reservoir (point 1) to the summit (point 2 elev = 22m) is 3 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. Determine the velocity in the siphon in m/s? Photo for this problem is attached below.
an open rectangular tank mounted on atruck is 8 m long and 1 m. wide. it is filled with water to a depth of 3.69 meters. if it is accelerated at 10.16 m/s^2 along its length, determine the required height (in meters) of the tank to prevent any water from spiling.