The output of a compressor plant delivering 600 m3 of free air/hr at 7 bar gauge at 20 oC passes through arefrigeration type dehumidifier where it is cooled to 1 oC. How much water should be collected from thedehumidifier per hour ?Please choice one below:a. 5.124 kg/hrb. 0.909 kg/hrc. 0.408 kg/hrd. 3.275 kg/hre. 1.317 kg/hr Pressure (Bar Gauge)Temparature °C2468.0.48D.170.100.070.05..............201.73D.576 0.346 0.247 0.192......405.101.701.020.728 0.5676012.95 4.322.591.851.448029.04 9.685.814.153.2310056.00 19.33 11.76 8.406.531200.036.73 22.04 15.74 12.241400.0D.037.74 29.96 20.97Mass of water (kg) per 100 m3 of free saturated air.

Answered: Image /qna-images/answer/89c3e33c-52ab-4732-9c8c-08cd4b57271e.jpg

The output of a compressor plant delivering 600 m3 of free air/hr at 7 bar gauge at 20 oC passes through arefrigeration type dehumidifier where it is cooled to 1 oC. How much water should be collected from thedehumidifier per hour ? Please choice one below: a. 5.124 kg/hr b. 0.909 kg/hr c. 0.408 kg/hr d. 3.275 kg/hr e. 1.317 kg/hr

The output of a compressor plant delivering 600 m3 of free air/hr at 7 bar gauge at 20 oC passes through arefrigeration type dehumidifier where it is cooled to 1 oC. How much water should be collected from thedehumidifier per hour ? Please choice one below: a. 5.124 kg/hr b. 0.909 kg/hr c. 0.408 kg/hr d. 3.275 kg/hr e. 1.317 kg/hr

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

Scales that to meet the assumption of Normality are classified as
The coefficient of bend value in the energy loss due to bend in a pipe depends on the radius of curvature of bend, _________________, & angle of bend.
Convert 22C to Fahrenheit.
The coefficient of bend value is the energy loss due to bend in a pipe depends on the pipe diameter, _________________, & radius of curvature of bend. Friction in the pipe bend Bend pipe material Length of the bend pipe Angle of bend
For a given single cylinder engine the piston displacement, Pd is 600 cc, the stroke is 12 cm and the clearance volume is 85.7 cc, what is the bore of the engine? a. 7.98 cm b. 63.67 cm c. 15.91 cm d. Cannot be determined Show solution. Please answer honestly and do not just guess. Thank you :)
The length of a iron bar is measured by a number of different observers and the following set of 12measurements are recorded (units mm)302,304,303,305,307,309,310,311,312,301,303,302. Find the values of mean, median, variance andstandard deviation.
8.. An air blower is to deliver 40,000 ft3 /min. Two U-tube gages measure suction and discharge pressures. The suction gage reads a negative 2′′ of water. The discharge gage, located 3 ft above the point to which the suction gage is attached, reads +3′′ of water. The discharge and suction ducts are of equal diameter. What size motor should be used to drive the blower if the overall efficiency is 68% (γ = 0.0750 lb/ft3 for air)? indicate free body diagram
Please answer it in 30 mins. show solutions step by step with units
answer qiuckly
ques 6 part b plz answer asap
answer asap plz
How did we get to 193.185?