The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 101 GPa] with a cross-sectional area of A₁ = 580 mm². Bar (2) is an aluminum alloy [E = 75 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 57 kN acts on the structure at D. Assume L₁-780 mm., L₂-390 mm., a-690 mm., b=360 mm., and c=1160 mm. Determine: (a) the normal stresses 0₁, 0₂ in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i (1) L₁ L2 (2) B MPa, 0₂ = i mm. D MPa

The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 101 GPa] with a cross-sectional area of A₁ = 580 mm². Bar (2) is an aluminum alloy [E = 75 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 57 kN acts on the structure at D. Assume L₁-780 mm., L₂-390 mm., a-690 mm., b=360 mm., and c=1160 mm. Determine: (a) the normal stresses 0₁, 0₂ in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i (1) L₁ L2 (2) B MPa, 0₂ = i mm. D MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam AB = 10 m has a hollow rectangular cross-section with 14 cm as width, 23 cm as depth, and inner thickness as 1 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
SOLVE for the AXIAL LOAD at HI
The block has a weight of 20 lb and is being hoisted at uniform velocity. Determine the angle θ for equilibrium and the force in cord AB.
The 3 bars are made of steel and form a pin-connected truss. Each bar has a cross sectional area of 3 in^2. Use Est = 29x10^6 psi. f the truss was constructed at 50 F and is heated to 110 F, coefficient of thermal expansion of steel = 6.6x10^-6 ft/ft F. Determine the: a) Force in bar AD (kip), and b) Force in bar AB (kip).
Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.
Which of the following is the nearest value for the force at member AC? a. 3.4 kN tension b. 3.4 kN compression c. 1.7kN compression d. 1.7kN tension
The 30-mm-diameter A-36 steel rod is subjected to the loading shown. Determine the displacement of end A with respect to end C.
2.) Given the truss shown, determine the value of the horizontal reaction at B. C= 14 KN D=20 KN E = 54 KN F = 61 KN g= 7 m The answer must be in KN.
Example 2: Rigid rod supported by BDE, AB and CD. AB is made of aluminum (E = 70 GPa) and its area is 500 mm2, CD is made of steel (E = 200 GPa) and its area is 600mm2. Find a) the displacement at B b) the displacement at D c) the displacement at E due to the 30kN force acting at the end of E. Solution: We find the forces from the free body diagram of BDE.
FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(10^6) mm^4.
Solve for ED, EH, and GH. F1 = 45kN, F2 = 25kN
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.