The pin in the image shown belowmust transfer an axial tension force of12.7 kN. Calculate the minimum pindiameter. Use Shear stress-D0.4"Yieldstrength. Assume material is 1020hot-rolled steel. *P2ShearPlanesPin

First we need to find the value of yield strength using steel through internet.

Answered: The pin in the image shown below must…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

idity modulus doengro 17. A 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is as aeqml 19WOL to da odt ons aasmos m noienet ni mioj по djiw YIVO P/24 F 12mm ↑ P/2 00 8mm 8mm
A gusset plate is connected to the flange of column with the help of fillet weld on both sides as shown in the figure. The direct shear stress and bending tensile stress are 70 MPa and 130 MPa respectively. Find the equivalent stress (in GPa). Gusset plate I-section flange
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 3/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 3/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 6.0 kips. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 5/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 5/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 8.0 k. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4*Yield strength. Assume material is 1020 hot-rolled steel. *

The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4Yield strength. Assume material is 1020 hot-rolled steel.