PROBLEM 2The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at sectionA with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine(a) The velocity at section B, V (m/s)(b) The pressure at section B, ps (kPa)(с) Fмх (N)(d) FMY (N)(е) Fpx (N)(f) Fpy (N)(g) The x-component of the reaction by the bend, FRx (N) and(h) The y-component of the reaction by the bend FRY (N).de = 100 mmB-da = 150 mm30°

Calculation of pipe bend problem

The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine

The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil with sp. gr. 0.95 flows at 200 lit/sec through a 500 m of 200 mm diameter pipe (? = 0.0225). Determine (a) the head loss (m) and (b) the pressure drop (kPa) if the pipe slopes down at 10⁰ in the direction of flow.
Oil (µ = 0.35 Pa-sec) flows through a horizontal 20 cm diameter circular pipe. The velocity at any point in the pipe’s cross-section a distance at a distance y from the center is: V =64(r² − y²) / μ where: r = 10 cm (radius of the pipe) Determine the following: a) Maximum flow velocity (m/sec) b) Shear stress (Pa) at the pipe’s centerline c) Shear stress (Pa) at the pipewalls?
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
Medium oil having a sp.gr. of 0.90 flows through a 120 mm diameter pipe with a mean velocity of 5.3 m/s and friction factor of 0.01. Oil has an absolute viscosity of 0.04 Pa.s. Compute the velocity at the center. CHOICE: 3.60, 6.003, 6.30, 3.006
A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.
Oil (SG = 0.89), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.049 ft3/s. Determine the head loss per unit length of this flow.
Include a free body diagram. A 12′′ pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the pressure at point A in the pipe is 40 psi. A differential gage is attached to the pipe at A and at a point Bdownstream that is 10 ft higher than A. The deflection of mercury in the gage is 3.33 ft, indicating a greater pressure at A. What is the lost head A to 5?
For the same condition as the previous problem (After a solid block is put on a scale in the water tank as shown in the picture, the total water volume level increases from 5.0 m3 to 6.0 m3. The reading from the upper spring scale is 36.9 kN, and the reading from the scale in the water is 30 kN. The specific weight of water is γw=9.81kN/m3. ), select the correct equilibrium equation alone the vertical direction:______ A. Fb + Fspring=w B. Fb+Fspring-Fscale=w C. Fb+Fspring+Fscale=w D. Fb-Fspring-Fscale=w
Topic: hydraulics A pipe carrying oil of specific gravity 0.877 changes in size from 150mm at section 1 and 450mm at section 2. Section 1 3.6m below section 2 and the pressures are 90kPa and 60kPa respectively If the discharge is 150 ht sec determine the head lost and the direction of the flow.
A pipe bend tapers from a diameter of 500 mm at inlet to a diameter of 250 mm at outletand turns the flow through an angle of 45°. Measurements of pressure at the inlet andoutlet show that the pressure at inlet is 40kN/m2 and the pressure at outlet is23 kN /m2 . If the pipe is conveying oil which has a density of 850 kg/m3 , determine themagnitude and direction of the resultant force on the bend when the oil is flowing at therate of 0.45 m3⁄s. The bend is in a horizontal plane.
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
CORRECT LETTER PLS 1. In a system with 4 reservoirs and 1 pipe junctions, how many hydraulic headloss equations are formulate? A. 3B. 2C. 1D. 4E. 5 2. In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is true and JB is false B. BJ is true and JB is true C. BJ is false and JB is false D. BJ is false and JB is true 3.which of the following is always the same for horizontal closed conduit? A. Total headB. Velocity headC. Elevation headD. Pressure head