The pipe flow in the figure shown below is driven by pressurized air in the tank. What gage pressure pi is needed to provide a 20°C water flow rate Q= 60 m/h? The total length of the pipe, which includes the vertical section measuring 80 m, is 130 m. For water at 20°C, take p= 998 kg/m3 and u= 0.001 kg/m-s. Take fsmooth = 0.0136. Smooth pipe: d = 5 cm Open jet P1 10 m The required gauge pressure is Pa.

The pipe flow in the figure shown below is driven by pressurized air in the tank. What gage pressure pi is needed to provide a 20°C water flow rate Q= 60 m/h? The total length of the pipe, which includes the vertical section measuring 80 m, is 130 m. For water at 20°C, take p= 998 kg/m3 and u= 0.001 kg/m-s. Take fsmooth = 0.0136. Smooth pipe: d = 5 cm Open jet P1 10 m The required gauge pressure is Pa.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

Water 60°F flows at 10 ft/s in a 3 in. diameter pipe that is 100 ft long. There are six elbows (KL = 1) and two gate valves (KL = 0.3). The end of the pipe is at elevation 20 ft above the inlet. The pressure at the inlet is 50 psia. The roughness height is 0.0002 ft. Determine the head at the inlet, head loss,pressure drop due to losses, and absolute pressure at the end. *Show your correct and complete solution. Please include schematic diagram and assumptions.*
A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil (s.g.=0.88) and the pressure in the smaller pipe is 265 kPa what force is exerted on the contraction, neglecting friction?
A certain amount of water (H2O) flows permanently into the pipe venturi(image2) in the figure next to it. In the stretch considered between (1) and (2), it is assumed the losses by friction that were despicable and the uniform properties in the sections are assumed. The entrance area is A1 while that of throat is A2 (A1 > A2). A pressure gauge whose manometric fluid is Mercury Hg (YHg> YH2O) is connected between the input sections and the throat. Show, without omitting any calculation steps that the flow rate at the input (1) is given by(image1):
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
A water tank used for fire fighting is shown in the figure. A fire extinguishing installation was installed by the cast iron pipe (roughness value ε=0.005mm) from the steady, incompressible water flow for pipe length Lpipe=126.2 m and pipe diameter D=106.2 mm. The height of the tank from the pipeline is h= 24.62 meters. A gate valve is placed on the end line of the installation. Accept that the local pressure loss equivalent length of the gate valve is given as Le/D=8.62, neglect other local pressure losses in the pipe line installation. In places 1 and 2 shown in the figure, the pressure is atmospheric pressure. i-Accordingly, calculate the speed, volumetric flow rate and mass flow rate of the water when the gate valve is opened in this installation. Repeat the calculation at least three iteration, if necessary, you can do more iteration. (ii) Calculate how much electrical energy can be produced if a hydraulic turbine with a total efficiency of 7a.b% is placed in front of the valve…
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
A 150 mm horizontal waterline contracts abruptly to 75 mm diameter. A pressure gage 150 mm upstream from the contraction reads 34.5 kPa when the mean velocity in the 150 mm pipe is 1.5 m/s. What will pressure gages read 0.6 m downstream and just downstream from the contraction if the diameter of the vena contracta is 61 mm? Neglect pipe friction
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3