Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43: The position of member ABC is controlled by the hydrauliccylinder CD. For the loading shown, determine the force exerted bythe hydraulic cylinder on pin C when 0 = 55°.0.8 m0.5 m90°Ө10 kNB.D-1.5 m-

Name: Referring to Prob. 10.43 and using the value found for the force exert
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43: The position of member ABC is contr

Consider the given configuration of frame.

Engineering

Mechanical Engineering

The position of member ABC is controlled by the hydraulic cylinder CD. For the loading shown, determine the force exerted by the hydraulic cylinder on pin C when 0 = 55°. 0.8 m 0.5 m 90° Ө 10 kN B. D -1.5 m-

The position of member ABC is controlled by the hydraulic cylinder CD. For the loading shown, determine the force exerted by the hydraulic cylinder on pin C when 0 = 55°. 0.8 m 0.5 m 90° Ө 10 kN B. D -1.5 m-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.32P

See similar textbooks

Similar questions

A steel rod is acted upon by the loading shown below. 50 mm2is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa.
A house with 932 kN weight is built on a steep slope defined by points A, B, and C. To help assess the possibility of slope failure (mud slide), determine the components of the weight in directions normal (perpendicular) to the slope.
Determine the magnitude of the force (lb) in member EG of the Pratt bridge truss shown if h = 12.9 ft and P = 82.02 lb. Round off only on the final answer expressed in 3 decimal places.
The barrier shown is commonly used during Highway Determine the weight per foot of length if it is made from plain stone concrete having a unit weight of 144 lb/ft3
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
The hoist supports an engine of weight W in kg. Determine the force the load creates in member DB and in member FB, which contains the hydraulic cylinder H. Given: X=2 m ; L=3 m ; W= 123 kg.
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 30599 lb, Q = 35388 lb, and y = 7.4 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 34150 b, Q = 33650 b, and y = 7.2 ft. Round off only on the final answer expressed in 3 decimal places, Instead of units, indicate whether the force is tensile or compressive: use Tif tensile and C if compressive.
A spherical gas tank has an inner radius of r = 1.5m, if it subjected to an internalpressure of p = 300kPa, determine its minimum thickness if the maximum normalstress is not to exceed 12MPa Note: indicate free body diagram.
A horizontal cable exerts a force of 399.971 pounds while holding a boom into place. Determine the angle the boom makes with the ground if it supports a 1000-pound load, as shown in the figure. Include fbd, given and solution.
All members of the truss have the same length L =4 m. Determine the magnitude (N) of the force supported by member BD if P = 473 N. Round off only on the final answer and expressed in 3 decimal places.
The assembly consists of two posts AB and CD each made from material 1 having a modulus of elasticity of E1 and a cross-sectional area A1, and a central post EF made from material 2 having a modulus of elasticity E2 and across-sectional area A2. If posts AB and CD are to be replaced by those having a material 2, determine the required cross-sectional area of these new posts so that both assemblies deform the same amount when loaded.