The potentiometer used in audio system is having a total resistance of 10K2 with maximum length of 8cm and supplied with 12V DC power supply. After the application of displacement, the wiper moved from 1.5cm to 4.5cm. Then |calculate the following, i. Sensitivity of the Transducer in volt/cm. ii. Change in resistance of the transducer. iii.Output voltage of the transducer. iv. Output voltage, when the wiper is moved to Ocm.

The potentiometer used in audio system is having a total resistance of 10K2 with maximum length of 8cm and supplied with 12V DC power supply. After the application of displacement, the wiper moved from 1.5cm to 4.5cm. Then |calculate the following, i. Sensitivity of the Transducer in volt/cm. ii. Change in resistance of the transducer. iii.Output voltage of the transducer. iv. Output voltage, when the wiper is moved to Ocm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The input resistance of the amplifier used in the oscillator circuit shown in the picture is very large. No-load voltage gain is given as K0 = 5. For L = 0.1mH; Calculate the value of C1 and C2 capacitors for the circuit to oscillate at f0 = 2MHZ.
With the conditions given below, if voltage is v(t) = 8sin4000pit mV, with the osciloscope, What are the Vs, Vd, Hs, and Hd?
Can you upload a schematic of ne5532 audio amplifier circuit with a gain of one? And explain your circuit
Using 741 op amp, design a suitable circuit to generate Binary Phase Shift Keyiing(BFSK) modulator. Design should perform in such a way that the BFSK output should contain a frequency of f1=2kHz when message signal is low and f2 =4kHz when the message signal is high. Take the frequency of message signal as 200Hz. Draw the clear circuit diagram and calculate the values of resistors and capacitors used.
Given the audio frequencies range from 10 Hz up to 40 kHz, calculate the sampling rate and hence find the maximum channel capacity if 8-PSK is utilized.
Select 1 transducer or sensor available in the market, with providing the brand, model, and technical specification of the selected transducer or sensor, you are required to i. Explain its designed measurand and the working range. ii. Explain its basic working principles and any steps required to take in order to avoid any error during the measurement process. iii. Identify either the selected transducer or sensor that required a signal conditioner. iv. Propose 1 cable which is suitable to be connected with the selected transducer or sensor.
Topic: Input and Output Characteristics of Transistor in Common Base Configuration Answer in 2-3 sentences each. Need a kind tutor that will do it for me. Thank you! 1. What are the applications of the common base (CB) configuration? 2. What are the output and input impedances of CB configuration?
a cassette player is said to have a signal to noise ratio of 58dB whereas for a CD player it is 95dB. what is the ratio of intensities of the signal and background noise for each device?
Normally in this process, a current to pneumatic transducer (I/P) of controlsystem receives a 15 mA of signal from the transmitter. Suddenly, thepressure drops across the fluidized bed decreased and not meet the productquality. After the checking, the signal transmitter reads at 10 mA. find the required to estimate the equivalent pressure signal transmitter controller in psig and identify its method.
21 - What is the arithmetic difference between the highest and lowest values of the input that being sensed?A) LinearityB) SpanC) RangeD) SensitivityE) Resolution
4. Choose the correct expression Select one:a. The input impedance of an amplifier is measured with the applied signal equal to zero.b. The output impedance of an amplifier is measured with the output signal equal to zero.c. The output impedance of an amplifier is measured with the applied signal equal to zero. 5. A BJT transistor to behave as an amplifier must be biased in the region of: Select one:to. cutb. Saturationc. Active 6. You cannot obtain ac domain amplification without applying a level ofdc polarization. Select one:TrueFalse
Sketch the output waveform for the circuit of Fig. below.