The quadlateral cycle concept offers appropriate limits in estimating the theoretical maximum for heat-to-power conversion systems. Calculate the maximum recoverable work (in kW) from an air stream of 325 300°C and 0.2 kgis, that can be cooled to 137°C Assume ambient 20°C as the sink and use appropriate specific heat value for air

The quadlateral cycle concept offers appropriate limits in estimating the theoretical maximum for heat-to-power conversion systems. Calculate the maximum recoverable work (in kW) from an air stream of 325 300°C and 0.2 kgis, that can be cooled to 137°C Assume ambient 20°C as the sink and use appropriate specific heat value for air

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.75P: Referring to Problem 1.74, how many kilograms of ice can a 3-ton refrigeration unit produce in a...

See similar textbooks

Similar questions

Refrigerators currently being manufactured in the United States are using______as their refrigerant.
Why is two-stage compression popular for extra-low-temperature refrigeration systems?
Compare the thermal efficiency of a two-stage gas turbine with regeneration, reheating, and intercooling to that of a three-stage gas turbine with the same equipment when all components operate ideally.
Why heat engines are intentionally equated at high temperatures?
Evaluate the performance of gas power cycles for which the working fluid remains a gas throughout the entire cycle.
A coal-burning steam power plant produces a net power of 300 MW with an overall thermal efficiency of 32 percent. The actual gravimetric air–fuel ratio in the furnace is calculated to be 12 kg air/kg fuel. The heating value of the coal is 28,000 kJ/kg. Determine the rate of air flowing through the furnace.
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: Enthalpies corresponding to the states indicated in the cycle (1, 2, 3 and 4); 1.a. The cooling rate (QL); 1.b. The work provided to the fluid by the compressor; 1.c. The work generated by the turbine; 1.d. The condenser heat rejection rate (QH); 1e. The coefficient of performance of the cycle;
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: Enthalpies corresponding to the states indicated in the cycle (1, 2, 3 and 4); 1.a. The cooling rate (QL);Response 1.b. The work provided to the fluid by the compressor;Response 1.c. The work generated by the turbine;Response 1.d. The condenser heat rejection rate (QH);Response 1 and. The coefficient of performance of the cycle;Response
for a thermodynamic work cycle that uses two turbines consisting of a (low pressure turbine) and (high pressure turbine), make a schematic of a WATER PIPE steam generator that can be used.
Steam at 20 MPa and 620°C enters a steam turbine and expands to a condenser pressure of 100 kPa. An open feedwater heater is added operating at 2 MPa. Calculate the cycle thermal efficiency in %. Use the unrounded values of the work of the turbine, work of the pump, and heat added when needed. Please use the green book entitled "Thermodynamics Properties of Water Including Vapor, Liquid, and Solid Phases by Keenan, Keyes, Hill, and Moore for the steam table.
Question 1 [20]Air at the beginning of an ideal Otto cycle is at 101.3 kPa and 15°C. The cycle has acompression ratio of 7, and 1000 kJ/kg of heat is transferred to air during the constantvolume heat-addition process. Using constant specific heats at room temperature, calculate,1.1 the pressure and temperature at the end of the heat- addition process,1.2 the net work output,1.3 the thermal efficiency, and1.4 the mean effective pressure for the cycle.
a Stirling engine to perform 20 kJ of work per cycle. How large would the engine need to be with a temperature difference of 300°C and a volume ratio of 2.3? Use helium as your working fluid.