The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a function of time t, initial energy of the explosion E, and average air density ? . Use dimensional analysis to express the relationship between R, t, E, and ? in dimensionless form.

The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a function of time t, initial energy of the explosion E, and average air density ? . Use dimensional analysis to express the relationship between R, t, E, and ? in dimensionless form.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.9P: When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the...

See similar textbooks

Related questions

Q: The lift of a wing, Fisft, is a function of wingspan, W, chord length, H, surrounding air density,…

A: Flift=fW,H,ρ,μ,V

Q: A tiny aerosol particle of density pp and characteristic diameter Dp falls in air of density p and…

Q: The height H that fluid rises in a liquid barometer tubedepends upon the liquid density ρ , the…

A: Consider a function Express each of these dimensional variables in their dimensional form,

Q: Example: The pressure difference (Ap) between two point in a pipe due to turbulent flow depends on…

A: ∆P=fV, D, μ, ρ ,e, L

Q: Consider laminar flow over a flat plate. The boundary layer thickness & grows with distance x down…

Q: When a steady uniform stream flows over a circular cylinder, vortices are shed at a periodic rate.…

A: Dimensions of frequency f→T-1 free stream velocity (V)= LT-1 Fluid density (ρ)=ML-3 Fluid viscosity…

Q: Algebraic equations such as Bernoulli's relation, are dimensionally consistent, but what about…

A: For an equation to be dimensionally consistent, each of the individual components of the equation…

Q: Use the method of repeating variables to find out the non-dimensional groups for the problem of fan…

A: To find: The non dimension group . Given: The power is function of p=f(D,ρ,ω,Q). Here, P is power, D…

Q: The bending stress o in a beam depends upon the bending moment Mand the beam area moment of inertia…

A: It is required to determine dimensionally homogeneous formula for bending stress

Q: The drag coefficient in aircraft industry affected by some parameters which are the speed of plane…

A: The drag coefficient will affect by parameters.

Q: The drag coefficient in aircraft industry affected by some parameters which are the speed of plane…

A: DRAG COEFFICIENT Drag Force (D) is defined as the force that opposes the motion of a fluid-filled…

Q: A liquid of density ? and viscosity ? is pumped at volume flow rate V· through a pump of diameter D.…

A: Write the dimensions of the given parameters.

Q: The output power W. of a spinning shaft is a function of torque T and angular velocity ? . Use…

A: Given Data: The torque acting on the shaft is The angular velocity of the shaft is ω. The output…

Q: The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal…

A: The complete derivation is attached as an image.

Q: 01: Consider laminar flow over a flat plate. The boundary layer thickness 8 grows with distance x…

A: As per our Q&A guidelines we are supposed to solve only one question at once kindly repost the…

Q: Power generated by a propeller operating in the air (P); it depends on the mass density of the air…

Q: A stirrer is used to mix chemicals in a large tank. The shaft power W . supplied to the stirrer…

A: Writing the dimension of the following,

Q: List the three primary purposes of dimensional analysis.

A: Dimensional Analysis is a mathematical technique that makes use of the study of dimensions as an aid…

Q: 1. Explain the three necessary conditions which must be met in order to achieve complete similarity…

A: The necessary condition which must be met in order to achieve similarity between a model and a…

Q: dus A fluid flow situation depends the on 2. Velocity (V), the density several linear dimension,…

A: Variables involved in this case,Velocity = VDensity =ρLinear dimensions=L, L1, L2Pressure…

Q: The force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of…

A: As it is given in the question that the force (F) depends in l, h, E, and γa. Here are the…

Q: In an experimental investigation, it is found that the discharge of oil through a pipeline relates…

A: Given Data Q=f(P,r,ρ,μ) f(Q,P,r,ρ,μ)=0 Hence, total no. of variables, n = 5 m=3 n-m=5-3=2 Pi terms…

Q: How can I use dimensional analysis to show that in this problem both Froude's number and Reynold's…

Q: MLT The resistin, .orce (F) of a supersonic plane during flight can be considered as dependent upon…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Given that The power output (P) of a marine current turbine is assumed to be a function of velocity…

Q: Q2/ By using the power series method make a dimensional analysis for he following variables: The…

Q: The period of a pendulum T is assumed to depend only on the mass m, the length of the pendulum `,…

A: The given variables are: Dimensional units for the different variables are:

Q: When a liquid in a beaker is stirred, whirlpool will form and there will be an elevation difference…

Q: The drag FD of the golf ball is affected by the speed V of the ball, the diameter d of the ball, the…

Q: Dimensional analysis can be used in problems other than fluid mechanics ones. The important…

A: T=fcnl,I,E,ρ,σ

Q: When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow and then undergoes…

A: Given Diameter of the pipe = D Acceleration = a Density = ρ Viscosity = µ Time = ttr To find…

Q: The thrust F of a propeller is generally thought to be afunction of its diameter D and angular…

A: The thrust force is the function of F=fD,ω,V,μ,ρ here n=6m=3 Now the replacing variables are μ,V,D…

Q: By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body…

A: Given Force = F Velocity = u Length = L Roughness = e Density of fluid = p Gravitational…

Q: The speed of sound c in an ideal gas is known to be a function of the ratio of specific heats k,…

A: To determine: develop a functional relationship between the given parameters. There are a total of…

Q: A- The power produced from a pump (P) is fun (Hon of flow (@), pressure drop (P), Density of fluid…

Q: 2. 21 If there are n variables in a particular flow situation, and these variables contain in…

A: If n=total number of variables m =number of fundamental dimensions Then the number of dimensionless…

Q: During World War II, Sir Geoffrey Taylor, a British fluid dynamicist, used dimensional analysis to…

A: Dimension analysis is the method of establishing a relationship between different physical…

Q: Suppose we know little about the strength of materials butare told that the bending stress σ in a…

A: Since the bending stress proportional to half the thickness of the beam, we can state that…

Q: A prototype automobile is designed for cold weather inDenver, CO ( - 10 ° C, 83 kPa). Its drag force…

A: First assemble the necessary air density and viscosity data: Denver:…

Q: lease solve this problem, Thank you very much! Figure is attached 1. liquids in rotating cylinders…

Q: During World War II, Sir Geoffrey Taylor, a British fl uiddynamicist, used dimensional analysis to…

A: Given data: E = f (R, ρ, t ) where R = blast wave radius , E = energy released, ρ = air density,…

Q: Force F is applied at the tip of a cantilever beam of length L and moment of inertia I Fig. . The…

A: There are five parameters that are listed below with dimensions, Force (F)- MLT-2 Length (L)- L…

Q: In making a dimensional analysis, what rules do you followfor choosing your scaling variables?

A: We have to explain the steps what we will follow for choosing spacing variables in dimensional…

Q: Speed is usually a function of density, gravitational acceleration, diameter, height difference,…

Q: generate a dimensionless relationship

A: Given: x-component fluid velocity u viscosity top plate speed\ distance h fluid density distance y…

Q: Q3: The power output (P) of a marine current turbine is assumed to be a function of velocity U,…

A: Data given- Power output P is a function of U,L,w,ρ,v

Q: When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow and then undergoes…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
During World War II, Sir Geoffrey Taylor, a British fluid dynamicist, used dimensional analysis to estimate theenergy released by an atomic bomb explosion. He assumed that the energy released E, was a function of blastwave radius R, air density ρ, and time t. Arrange these variables into single dimensionless group, which we mayterm the blast wave number.
The speed of sound c in an ideal gas is known to be a function of the ratio of specific heats k, absolute temperature T, and specific ideal gas constant Rgas. Showing all your work, use dimensional analysis to find the functional relationship between these parameters.
During World War II, Sir Geoffrey Taylor, a British fl uiddynamicist, used dimensional analysis to estimate theenergy released by an atomic bomb explosion. He assumedthat the energy released E , was a function of blast waveradius R , air density ρ, and time t . Arrange these variablesinto a single dimensionless group, which we may term theblast wave number .
The output power W. of a spinning shaft is a function of torque T and angular velocity ? . Use dimensional analysis to express the relationship between W., T, and ? in dimensionless form. Compare your result to what you know from physics and discuss briefly
Dimensional analysis is to be used to correlate data on bubble size with the properties of the liquid when gas bubbles are formed by a gas issuing from a small orifice below the liquid surface. Assume that the significant variables are bubble diameter D, orifice diameter d, liquid density rho, surface tension sigma (in N/m), liquid viscosity mu, and g. Select d, rho, and g as the core variables.
The speed of sound c in an ideal gas is known to be a function of absolute temperature T, universal ideal gas constant Ru, molar mass (molecular weight) M of the gas, and ratio of specific heats k. Showing all your work, use dimensional analysis to find the functional relationship between these parameters.
Use the first principle (dimensional analysis) to generate a dimensionless relationship for the x-component of fluid velocity u as a function of fluid viscosity μ, top plate speed v, distance h, fluid density ρ, and distance y.
The drag coefficient in aircraft industry affected by some parameters which are thespeed of plane (v), the plane length (L), the air density (ρ), the air dynamic viscosity(μ), and speed of sound (a). By using dimensional analysis, identify two non-dimensionnumbers in which the drag coefficient is a function of them and explain how these twowill effect on drag coefficient.
The thrust F of a propeller is generally thought to be afunction of its diameter D and angular velocity V , the forwardspeed V , and the density ρ and viscosity μ of the fl uid.Rewrite this relationship as a dimensionless function.
In making a dimensional analysis, what rules do you followfor choosing your scaling variables?
When a capillary tube of small diameter D is inserted into a container of liquid, the liquid rises to height h inside the tube (Fig.). h is a function of liquid density ? , tube diameter D, gravitational constant g, contact angle ?, and the surface tension ?s of the liquid. (a) Generate a dimensionless relationship for h as a function of the given parameters. (b) Compare your result to the exact analytical equation for h. Are your dimensional analysis results consistent with the exact equation? Discuss.