The rate of upward seepage taking place through a granular soil contained in a tank is 976.5 cm³/sec. Given that H1 = h = 1.8 m, the area of the tank = 0.62 m², void ratio of the soil = 0.55, the specific gravity is 2.65, and the hydraulic conductivity of the sand is 0.21 cm/sec, determine the following: d. If boiling will occur at h = 2.5 m? Justify your answer by showing the appropriate comparison by solving. e. The value of h to cause boiling. (は) H2 Valve (open) Inflow

The rate of upward seepage taking place through a granular soil contained in a tank is 976.5 cm³/sec. Given that H1 = h = 1.8 m, the area of the tank = 0.62 m², void ratio of the soil = 0.55, the specific gravity is 2.65, and the hydraulic conductivity of the sand is 0.21 cm/sec, determine the following: d. If boiling will occur at h = 2.5 m? Justify your answer by showing the appropriate comparison by solving. e. The value of h to cause boiling. (は) H2 Valve (open) Inflow

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.11P

See similar textbooks

Similar questions

A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
For a falling head permeability test, these valueare given: Length of the soil specimen = 200 mm Area of the soil specimen = 1000 mm2 Area of the standpipe = 40 mm2 Head difference at time, t = 0 min is 500 mm Head difference at time, t = 3 min is 300 mm1. Determine the hydraulic conductivity of thesoil in cm/sec.2. What was the head difference at time, t =100 sec?
Consider a clay layer drained at the the top and bottom as shown in figure. For the case of constant initial excess pore water pressure (ui=u0) and Tv=0.4 ,determine the degree of consolidation Uz at z/Ht.For the solution, start from eq.(6.32).
An impervious layer underlies 4 layers of permeable soil. The thickness and the coefficient of permeability each layer from top to bottom are: Evaluate the equivalent horizontal coefficient of permeability of the deposit in cm/sec. Evaluate the discharge of the aquifer in m3/day if the hydraulic gradient for the soil formation is 0.70.
At n = 0.45, the hydraulic conductivity of the sand is 0.010 cm/sec. Determine the hydraulic conductivity at n = 0.50.
For a sandy soil, the following are given: • Maximum void ratio = 0.72 • Minimum void ratio = 0.46 • Hydraulic conductivity at a relative density of 80% = 0.006 cm/sec. Determine the hydraulic conductivity of the sand at a relative density of 67%.
L = 370 mm A = 145 cm^2 h = 340 mm Water collected in 3 min Q = 580 cm^3 Void ratio of sand e= 0.66 Determine the Hydraulic conductivity and seepage velocity.
A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350mm. Calculate the hydraulic conductivity of this clay.
A soil profile consists of 2m of sand (γ=18kN/m³, kv=4 x 10-2m/day) over 3m of silt (γ=17kN/m³, kv=1 x 10-2m/day) over 2m of silt (γ=16kN/m³, kv=5 x 10-4m/day) over gravel. The water table is 0.5m below the ground surface. A piezometer placed at the top of the gravel layer measures a porewater pressure of 42kPa. Assuming a one-dimensional flow condition in the vertical direction, compute the flow rate in m³/day/m². Also compute, atmiddepth of the clay layer, the porewater pressure, total vertical stress, and effective vertical stress.
For a falling head laboratory test, the following are the given values:• Length of soil specimen = 210.00 mm• Initial head = 523.00 mm• Final head = 297.00 mm• Duration of test = 3.50 mins• Area of standpipe = 42.0 sq.mm• Area of specimen = 1050.00 sq.mmA. Compute for the hydraulic conductivity of the soil in cm/sec.B. Determine the seepage velocity if n=0.35C. Determine the head difference at t = 120 sec