The Resultant of the concurrent forces in the figure below is R = 201KN, pointing up along y-axis. Compute the value of 0 in degrees to givethis resultant. P1 = 470 and P2 = 205. Write the numerical value onlyand use two decimal places.P1y1RI+Yx130°FTwo cables are tied together at C and loaded as shown. Determine thetension in cable AC in KN. P = 3.71 KN, x1 = 6.0 m, x2 = 5.9 m, y1 = 5.0m, and y2 = 4.0 m. Write numerical value only and in 2 decimal places.BA2 mP2+ XCPx2y2

The components of a force can be seen with horizontal and vertical change when looking at the…

The Resultant of the concurrent forces in the figure below is R = 201 N. pointing up along y-axis. Compute the value of 0 in degrees to gi his resultant. P1 = 470 and P2 = 205. Write the numerical value onl and use two decimal places. P1 y1 R 30° x1 wo cables are tied together at C and loaded as shown. Determine t ension in cable AC in KN. P = 3.71 KN. x1 = 6.0 m, x2 = 5.9 m, y1 = n, and y2 = 4.0 m. Write numerical value only and in 2 decimal place B A P2 2m +X C P x2 y2

The Resultant of the concurrent forces in the figure below is R = 201 N. pointing up along y-axis. Compute the value of 0 in degrees to gi his resultant. P1 = 470 and P2 = 205. Write the numerical value onl and use two decimal places. P1 y1 R 30° x1 wo cables are tied together at C and loaded as shown. Determine t ension in cable AC in KN. P = 3.71 KN. x1 = 6.0 m, x2 = 5.9 m, y1 = n, and y2 = 4.0 m. Write numerical value only and in 2 decimal place B A P2 2m +X C P x2 y2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross section of a rectangular gate AB of width 2 m is shown in Figure2. The weight of the gate is 1 kN and is hinged along BB. The maximumtensile force that the cable can hold is only 44kN. Calculate the maximumwater depth, y that causes the cable to break and will cause the gate tofail/ open.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.
The maximum force that holds the 4-m-width gate in Figure Q2 (b) close is 50 kN. If oil is being added steadily, determine the maximum h before the gate starts to open. SGoil = 0.86.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 204 N and if a = 3m, determine the magnitude of force P(N). Round off only on the final answer expressed in 3 decimal places.
The tongs are used to grip the ends of the drillingpipe P. If a torque (moment) of MP = 800 lb ⋅ ft is neededat P to turn the pipe, determine the cable force F that mustbe applied to the tongs. Set θ = 30°.
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension TT in the restraining cable CD is 2.8 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take aa = 4.7 metres, and bb = 3.8 metres.
The power transmission cable in the figure below weighs 165 N/m. Using the table below, write down the numerical value of w. If h= 2.5m, determine the resultant horizontal and vertical forces the cable exert on tower BD.
Solve for support rections at A, B and C
Three cables are subjected to the horizontal force F at A as shown. The tension force TAB in cable AB is given 20 kN and joint A is in equilibrium.1) Draw the force diagram of the joint A; 2) Determine the unit vectors of TAB, TAC, and TAD; 3) Form three equilibrium equations in a scalar form for solving the magnitude of tension forces TAC, TAD, and horizontal force F; 4) Solve the magnitude of tension forces TAC, TAD, and horizontal force F. [Partial Ans: TAC = 50.7 (T) kN, F = 128 kN (right x direction)]
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm