The results of a compaction test on samples of soil that are to be used for an embankment on a highway project are listed below. Determine the maximum dry unit weight of compaction and the optimum moisture content. Sample No. Moisture Content Bulk Density (Ib/ft:) 4.8 7,5 145.0 3. 7.8 146.8 4 8.9 146.4 5 9.7 145.3

The results of a compaction test on samples of soil that are to be used for an embankment on a highway project are listed below. Determine the maximum dry unit weight of compaction and the optimum moisture content. Sample No. Moisture Content Bulk Density (Ib/ft:) 4.8 7,5 145.0 3. 7.8 146.8 4 8.9 146.4 5 9.7 145.3

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.7P

See similar textbooks

Similar questions

The following results were recorded during a Falling head permeability test: Sample diameter = 120 mm Sample length = 140 mm Initial head = 510 mm Final head = 310 mm Standpipe diameter = 6 mm Duration of flow = 3.4 mins Determine the coefficient of permeability for the soil in m/s. Based on the coefficient of permeability estimate the soil type
Results from liquid and plastic limit tests conducted on a soil are given below.Liquid limit tests: Plastic limit tests: PL = 19.1%a. Draw the flow curve and obtain the liquid limit.b. What is the plasticity index of the soil? c.Determine the liquidity index of the soil if Winsitu = 21%.
Following are the results from the liquid and plastic limit tests for a soil. Liquid limit test: Plastic limit test: PL = 18.7%a. Draw the flow curve and obtain the liquid limit.b. What is the plasticity index of the soil? c. Determine the liquidity index of the soil when the in situmoisture content is 26%
Problem # 1. A constant head permeability test is performed on a sample of granular soil. The length of the soil sample is 15 cm and the cross-sectional area is 10 cm^2. If a 24 cm^3 volume of water passes through the oil sample in a 3-minute period and the constant head is 30 cm determine the followinga. Determine the coefficient of permeability of the soil.b. Find the discharge velocity.c. Compute the seepage velocity if the void ratio is 0.64.
Standard proctor compaction test results on a sandy clay (35% sand, 55% clay, and 10% silt), taken from a borrow pit, are given in the following table. The sandy clay in the borrow pit has a porosity of 65% and a water content of 5.2%. A highway embankment is to be constructed using this soil. (a) Specify the compaction (dry unit weight and water content) to be achieved in the field. Justify your specification. (b) How many cubic meters of borrow pit soil are needed for 1 cubic meter of highway fill? (c) How much water per unit volume is required to meet the specification? (d) How many truckloads of soil will be required for a 100,000 m3 highway embankment? Each truck has a load capacity of 22.5 m3 and regulations required a maximum load capacity of 90%. (e) Determine the cost for 100,000 m3 of compacted soil based on the following: Purchase and load borrow pit material at site, haul 2 km round-trip, and spread with 200 HP dozer = $15/m3; extra mileage charge for each km =…
A soil sample has a unit weight of 1.9 g/cc and w=12%. If Gs of solids is 2.65, determine the volume of solids in cm3.
You are checking a field-compacted layer of soil. The laboratory control curve has the following values: gd (kN/m3) w (%) 16.34 14 16.57 16 16.65 18 16.50 20 16.26 22 15.87 24 The specification for compaction states that the field-compacted soil must be at least 95% of the maximum control density and within of the optimum moisture for the control curve. You dig a hole 1m3 in the compacted layer and extract a sample that weighs 17.2 kN wet and 14.1 kN dry. (a) What is the compacted gd? The compaction w? The percent compaction? Does the sample meet the specifications? (b) If the specific gravity is 2.68, what is the compacted degree of saturation? If the sample were saturated at constant density, what would be the water content?
A fresh soil sample with a mass of 460 g is collected from the field using a cylinder with diameter of 7.5 cm and height of 7.3 cm. After oven-drying, the soil mass becomes 370 g. What is the apparent specific gravity?
The following are the results from the liquid limit tests for a soil: Number of Blows, N Moisture Content, % 16 38.3 21 33.4 34 29.1 a) Draw the flow curve and obtain the liquid limit. b) If the Plastic Limit is determined to be 8%, what is the Plasticity Index of the soil? c) What is the Liquidity Index of the soil if the in situ w = 35%? What does this specific result tell us about this soil?
The results of a compaction test on the sample of soil that are to be listed are to be used for an embankment on a highway project are listed below . Determine the maximum dry unit weight of compaction and the optimum moisture content. The table is shown in image
From a standard Proctor laboratory sample of soil Gs= 2.70; maximum dry unit weight = 16.4 kN/m3; Optimum moisture content= 18%; Moisture content of soil at the borrow site+ 28%. Specification require that compaction of soil must be at least 95% of the maximum obtained from the proctor test. Compute the maximum compaction expected from the compacted soil using the zero air boids curve for this soil with the following moisture contents: w1= 20%; w2= 25%; w3= 30%.
A soil sample has a unit weight of 1.9 g/cc and w=12%. If Gs of solids is 2.65, determine the degree of saturation and porosity in percent.