I need answer within 20 minutes please please with my best wishes The reversible first-order gas reaction1A2R2is to be carried out in a mixed flow reactor. For operations at 300 K thevolume of reactor required is 100 liters for 60% conversion of A. Whatshould be the volume of the reactor for the same feed rate and conversionbut with operations at 400 K?Data: ki103 exp [-2416/T]AC, = CpR - CpA = 0AH, = -8000 cal/mol at 300K%3DK = 10 at 300 K%3DFeed consists of pure ATotal pressure stays constant

Answered: Image /qna-images/answer/80edfcb9-e6f1-43ed-b648-ebb649575617.jpg

The reversible first-order gas reaction 1 A2R s to be carried out in a mixed flow reactor. For operations at 300 K the volume of reactor required is 100 liters for 60% conversion of A. What hould be the volume of the reactor for the same feed rate and conversion out with operations at 400 K? Data: k¡ = 10° exp [-2416/T] AC, = CpR - CpA = 0 AH, = -8000 cal/mol at 300 K %3D K 10 at 300 K Feed consists of pure A Total pressure stays constant

The reversible first-order gas reaction 1 A2R s to be carried out in a mixed flow reactor. For operations at 300 K the volume of reactor required is 100 liters for 60% conversion of A. What hould be the volume of the reactor for the same feed rate and conversion out with operations at 400 K? Data: k¡ = 10° exp [-2416/T] AC, = CpR - CpA = 0 AH, = -8000 cal/mol at 300 K %3D K 10 at 300 K Feed consists of pure A Total pressure stays constant

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.28P

See similar textbooks

Similar questions

What is the volume of the isothermal, isobaric plug flow reactor can produce 80% conversion of the following reaction (4A  R + 6S) if the feed is gas phase at 649°C and 460kPa, given that the reaction rate is - rA = 10CA (mole/dm3 .h)
Combustion in a diesel engine is assumed to begin at TDC and proceed at constant pressure. The air/fuel ratio is 27/1, the calorific value of fuel is 43 MJ/kg, and the specific heat of combustion products is given by: Cy = 0.71 + 20x10-5 T where Tis the combustion products temperature in K unit. The gas constant for these products is taken to be 0.287 kJ/kg K. If the compression ratio is 15/1, and the temperature at the end of compression is 870 K, find at what percentage of the stroke the combustion is completed. 2312w
LNG is transported in specially designed vessels with specially insulated storage tanks and cryogenic facilities for handling LNG Select one: True False
A mix fresh feed A at temperature 20 °C is heated to reaction temperature of 180 °C, before feed to reactor 1. Upon completion of the exothermic reaction, the products from reactor 1 are feed to reactor 2 and distillation column, respectively, in a pre-determined ratio. The product stream temperature of reactor 1 has to be reduced from 250 °C to 40 °C, prior to the separation process. On the other hand, a fresh feed B is heated from 140 °C to the reaction temperature of 230 °C and react with the product stream from reactor 1, in reactor 2, under endothermic condition. Subsequently, the product from reactor 2 is cooled from 200 °C to 80 °C, after the reaction. The chemical process is illustrated in Figure 3.1. The process stream data is shown in Table 3.1. a) Determine the pinch temperatures, minimum load of the hot utility and cold utility, respectively, using Problem Table Method by shifting both hot and cold temperatures and for minimum temperature difference of 10 °C. Show all…
A proposed alternative diesel fuel contains 50% finely powdered bituminous coal and 50% ethanol by weight. The coal contains 4% moisture, has been cleaned of ash, and has an as-received HHV of 25 MJ/kg. Assume the coal has 5% hydrogen and 40% volatiles as-received. Find the as-received LHV of this fuel. Estimate the as-received mass fraction (%) of volatiles and the mass fraction (%) of fixed carbon in this fuel.
Methane fuel is burned with air in a boiler system (open system). For this system, the HFK value for the air supplied to the combustion environment is 1.4. If the temperature and pressure of the air and fuel entering the combustion environment is 25 ° C and 1atm, we calculate the flue gas temperature value of the boiler, assuming that the boiler's thermal efficiency is 60%. All reacting species and reaction products are perfect gases. There is no water condensation in the products. METANAID = 50000 kJ / kg HFK = Air excess coefficient All reacting species and reaction products are excellent gas. Products "no water condensation.
Q4) A small, low emission, stationary gas turbine engine operates at full load (3950 KW) at an equivalence ratio of 0.286 with an air flowrate of 15.9 kg/s. The equivalent composition of the fuel (ethane) is C2 H6. Determine the fuel mass flowrate and the operating air-fuel ratio for the engine
the dryness fraction of a sample of wet steam measured by a combined separating and throttling calorimeter is 0.9. The quality of steam after partial seperation is 0.28 kg of moisture in the separator increases to 0.95. calculate the total mass of the wet steam sample.
A six cylinder 4-stroke petrol engine with bore 120 mm and stroke 180 mm under test, is supplied petrol of composition C= 82%, H, = 18% by mass. The orsat gas analysis indicated that CO, = 12%, 0, -4% and N₂ = 84% by volume. Determine (1) Air-fuel ratio
SN=21
What is the difference between Auto ignition temperature, Fire Point and Flash point of a fuel? What will happen if you keep Auto ignition temperature close to fire point of a fuel on P-Theta diagram?
Describe what is done in the combustion process in the combustion chamber of a gas turbine to overcome the problem of a very low laminar flame speed compared to aircraft speed and a limited flame limit range? Explain with long expalanation max in 2 hours thank u