The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine the maximum force P that can be applied if the movement of (P) is limited to 10 mm. Neglect the wieghts of all members. Aluminum L= 2 m A = 500 mm² E = 70 GPa A 3 m 3 m 3 m C 3 m 0 B Steel L= 2 m A = 300 mm² E = 200 GPa 0 D P = 153 KN P = 133 KN

The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine the maximum force P that can be applied if the movement of (P) is limited to 10 mm. Neglect the wieghts of all members. Aluminum L= 2 m A = 500 mm² E = 70 GPa A 3 m 3 m 3 m C 3 m 0 B Steel L= 2 m A = 300 mm² E = 200 GPa 0 D P = 153 KN P = 133 KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.10P: A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete...

See similar textbooks

Similar questions

An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange B to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1).
The bar ABCD has rigid supports and consists of three prismatic solid segments, as shown. The end segments have cross-sectional area A1 = 840 mm2 and length L1 = 200 mm. The middle segment has cross-sectional area A2 =1260 mm2 and length L2= 250 mm. Loads PB and PC are equal to 25.5 kN and 17.0 kN, respectively. Determine the magnitude of the compressive axial force FBC (kN).
The rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.
In the element in the figure, the bars are made of UNSG 10100 HR steel (Sy= 26 Kpsi and E= 30x106 psi). Determine the maximum weight that the system can support.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5 mm and 2 mm, respectively. If the cables have a normal ultimate stress of ?u = 400 ???. Determine: a) The safety factor in cable AB b) The safety factor in cable BC Please add the free body diagram.
Find the load on each bar of the cage given below. Its dimensions are base 2a and height 3a. EB passes through the midpoint of the lattice. Angle of force F1= 700 with horizontal (choose an angle between 15o and 75o)
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places