The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?

The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
A hollow cast-iron pole has an outside diameter of 450mm and an inside diameter of 350mm. It is subjected to a compressive force of 1000kN (weight included) throughout its length of 1.0m. The pole is braced to prevent bending and buckling. E = 100 GPa.1. If the allowable stress for the pole is 15MPa, is the pole safe if a 1000kN compressive force is applied to it? (Prove your answer)2. If the allowable contraction for the pole is 0.15mm, is the pole safe or not?
The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are ơt=40 MPa, ơc=80 Mpa, and Ʈ=12 MPa.
A circular steel rod of diameter d is subjected to a tensile force P = 3.5kN The allowable stress in tension and shear are 190.6 MPa and 70.3MPa, respectively. What is the minimum permissible diameter dmin of the rod (in mm)?
A beam is supported as shown, and its cross-section is rectangular with a=5 cm and w= 2 cm. What is the maximum compressive stress that the beam is subjected to? At what point, A B C or D, the compressive stress is maximum?
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming thatthe rods were initially stress-free, what is the largest load P that can be applied without exceedingstresses of 150 MPa in the steel rod and 70 MPa in the bronze rod?
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
A beam with a T-section is supported and loaded as shown in the figure. The cross section has width b = 2 1/2 in., height h = 3 in., and thicknesst =3/8 in.(a) Determine the maximum tensile and compressive stresses in the beam.(b) If the allowable stresses in tension and compression are 18 ksi and 12 ksi, respectively, what is the required depth h of the beam? Assume thatthickness t remains at 3/8 in. and that flange width b 5 2.5 in.(c) Find the new values of loads P and q so that the allowable tension (18 ksi) and compression (12 ksi) stresses are reached simultaneously forthe beam. Use the beam cross section in part (a) (see figure) and assume that L1, L2, and L3 are unchanged.
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.
Figure 2 shows the stress at point A of I-section beam. status given. a) Calculate the principal stresses, location and angle. b) In a section a-a with an angle of 30 shown in the figure the stress components that will affect the existing plane calculate.