the rim and face alignment method is?

Q: Expandable pattern is used in ?

A:

Q: Impact velocity equation

A:

Q: Match the following. Screwing is an example of Lapping is an example of

A: Solution:

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the…

Q: triple beam balance?

A: Explanation given below.

Q: When the work done is positive?

A: The work is measured as the energy transfer between to states. Work done is simply the measure of…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: Which type of edge preparations are easier to make/prepare? Bevel grooves OJ grooves U grooves O…

A: Concept: 1) For j and u grooves we need customised form tool cutter. They can't be prepared use…

Q: Where did the 107.11 came from

A: Given   Weight, W1 = 500 N                 W2 = 1000 N Find   The angle 107.11o

Q: the temperature drop across the

A: Given; For the given material the temperature drop and the heat flow will be maximum : Material is,…

Q: Please send Complete answer for getting upvote  Detailed answer  what is Flyweight Design Pattern…

A: given; what is Flyweight Design Pattern Application  Real world example

Q: Please answer with working and answer also label the parts please

A: Note: Since we only answer up to 3 sub-parts, we'll answer the first 3 i.e., (a, b, c).  Please…

Q: the most suitable grindirg i firafion

A: Given; Base of a brass bracket needs rough grinding, For this purpose find suitable grinding wheel…

Q: if the f Re 20 -0.25 mm %3D De terminef?

A: Relative roughness, eD=0.25Reynolds number, Re=20

Q: Reviewed and update Which type of jig do not have base plate? | प्रकार के जिग में बेस प्लेट नहीं…

A: Given Jig To find Jig without base plate

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: The time of impact, must be 4.14. Show complete solutions. TY!

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: What are two common ways to provide for the kerf spacing?

A: Solution: Kerf space is a width of space that is developed in cutting processes when the material is…

Q: Q2: Can cBN be used in honing stick in single layer configuration?

A: Yes, CBN can be used in honing stick in single layer configuration. Honing stick with CBN makes…

Q: What is the percentage of rods

A: Given; Determine the percentage of rods whose lengths lie between 438 mm and 441 mm.Where, The…

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: hearing stress value will be The angle of twist will be

A: Solution:- Given data:- T =400 N-mt = 2mmG =28 Gpa Area of tube, =40×20+π×1022957.079mm2 Total…

Q: Draw a FBD the tip to tail method please show steps

A:

Q: Draw a sectional front view, top view and side view for Hexagonal bolt (M d mm *L mm)?

A: Given Hexagonal Bolt To find Sectional front view Sectional top view Sectional side view

Q: On increasing the value of rake angle, the strength of tooi.

A: Rake angle is defined as the angle between the normal line to the workpiece and the edge of the…

Q: :In impact testin

A: Hi and thanks for the question. Since you have asked multiple questions, we will solve the first…

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: When the work done is negative?

A: If the displacement of the body is in the direction opposite to the force, then work done is…

Q: A circular heeps is roll when it's start rolling e ¢ on vurtical positic Callt

A: Givenradius of the hoop r=1mangular velocity ω=1rev/stime t=1 sec

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: What is the sliding block?

A: To Define: Sliding block

Q: 17 in 43 in E

A: refer below images.

Q: Which one of the folowing is not correct ?

A: Given; The maximum shear stress theory predicts that shear yieldvalue ζy is 0.5 times the tensile…

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: the tool life for

A: Given; Determine tool life for maximum production rate. Where data is given as ; Taylor's tool life…

Q: Define how to calculate the central angle of sliding slope in case of friction circle method?

A: A friction circle is a graphical tool that conveniently defines the course of action of the…

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: How would a small or tight tolerance affect the layout?

A: The lines that are used for locating the points on the objects and items for the purpose of cutting,…

Q: rd frame and dr.

A:

Q: Why are some joints back gouged?

A: Gouging is important for any task related to welding when the operator removes material to get a…

Q: a. Calculate the Tap Drill Size, show all working our (i) M20 x2.5 (ii) 3/4" BSW iii) 5/16" BSW 18

A: Given    Drill tap, i = M20 x 2.5                  ii = 3/4 BSW                  iii = 5/16 BSW 18…

Q: bullet's speed?

A: To find Bullet speed

Q: . How can discontinuities in the root face be removed?

A: Discontinuity is a defect, it is an interruption of the typical structure of a material, such as a…

Q: draw the assembly in cross-section.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.