The RLC network given in the figure is supplied from the source of unknown voltage. After using a multimeter, it is found that VAB VBC- 100V and source current has a magnitude of 5 Ampere. The reactive power supplied by the source is equal to capacitive reactance. VAR (Round off to two decimal places. Assume resistance is R A Is 140.2 O 153.6 O 146.4 O 135.8

The RLC network given in the figure is supplied from the source of unknown voltage. After using a multimeter, it is found that VAB VBC- 100V and source current has a magnitude of 5 Ampere. The reactive power supplied by the source is equal to capacitive reactance. VAR (Round off to two decimal places. Assume resistance is R A Is 140.2 O 153.6 O 146.4 O 135.8

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

a) What is the time domain expression for the current? b) If the load impendance is created by an inductor with value L=375 mH, find the phaser voltage Vx? c) If the load impendance is created by a capacitor with value C=16.7 uF, find the phaser voltage Vx?
A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
A series RLC circuit having values of ? = 250Ω, ? = 3??, and ? = 4?? is shunted across a sinusoidal voltage given by the expression ?(?) =200 sin(200?? − 16°) ?. Look for the following: a. The equivalent impedance of the connection b. The phasor and instantaneous current flowing through the connection c. Draw the phasor diagram of the supply voltage and the total current. What is the phase difference of the two? d. What is the phasor and instantaneous voltage across the capacitor? e. If a 75?? capacitor is shunted across the load, what is now the value of the equivalent impedance in the connection?
A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power and the transmission line is compensated with a series capacitance of 0.5 Pu. Find the load angle with series capacitance compensation ?
Solve for the steady-state values of iR in milliampere (mA), and VC in Volts (V) for the circuit shown below, assuming that the circuit has been connected for a long time.
Exercise 11) Transform the circuit in phasor domain representation2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of voltage across resistor and capacitor5) Convert in rms values.
Application of Complex Number to EE (25 pts). Using Ohm’s Law (? = ? × ?), determine the following given a component having an impedance (Z) equation below and a current (I) equation passing through it. ? = (?? ??)^? + (? − ??)^?/? ohms; ? = ? ? amps a. Evaluate and simplify the component’s impedance (Z). Express your answer in polar form and in ohms. Use the principal root value only (if applicable). b. Evaluate and simplify the current (I) passing through the component. Express your answer in polar form and in amperes. c. Using Ohm’s Law (? = ? × ?), determine the voltage (V) across the component. Express your answer in polar form and in volts.
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?
A RL network supplied with 10V battery Find the mathematical expressions for the transient behaviour of vl, iL, VR2 and VR2 when the switched is moved to position 2. Sketch the curves of vL, iL and VR2. Then find How much time must pass before it can be assumed, for all practical purposes, that iL =0A and vL = 0 Volt? PLEASE STEP-BY-STEP STEPI NEED THEM TO STUDY.
Select the forward path gain (M ktop) for the system for the SFG diagram given below
Kindly answer the what is asked wherein the %n at full load, 0.8 lagging is 90.48%, Solve for the %n at 80% of the load and the nmax of it with 0.8pf lagging. Moreover, show me a complete, clean, step by step solution so that I can understand.
Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the voltage and current at R1, total power (apparent) delivered by the current source, draw the phasor diagram of the voltage and current at the source. Also, is the circuit inductive, capacitive, or neither (resistive)? please give the step-by-step solution NOTE: Polar form for Voltage & Current. Rectangular form for Impedance