The rod ABC is made of an aluminum for which E = 71.5 GPa. Knowing that P = 6.32 kNand Q = 46.66 kN,determine the deflection (in um) of point B if y = 0.44 and z = 0.51. Round off the final answer in four decimal places. ... 20-mm diameter B I 60-mm diameter

The rod ABC is made of an aluminum for which E = 71.5 GPa. Knowing that P = 6.32 kNand Q = 46.66 kN,determine the deflection (in um) of point B if y = 0.44 and z = 0.51. Round off the final answer in four decimal places. ... 20-mm diameter B I 60-mm diameter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Which of the following statements is correct about the given structure? O pin roller I fixed It is…

Q: It is known that the principal stresses acting in the vertical plane are 50 kPa and 100 kPa in the…

Q: C.6 (a) A manometer shown in Fig. C.6a is used to measure the pressure difference between two points…

Q: 3) For the beam loaded as shown in the figure, using area method; draw the shear and bending moment…

A: A beam arrangement is given as shown in figure above, And it has been asked in the question to draw…

Q: ve the following problems: 1. Determine the force in each bar of the truss shown in figure caused by…

A: The load is lifted at constant velocity, the forces involve is similar to forces under static…

Q: What will be the designed section of a pier cap (Let b = h/2) for a simply supported 25-meter span…

A: Given, L = 25 m γc = 23.6 kN/m3

Q: Calculate the forces in the required members of the truss F1 F2 H h В 4 @ S kN use 2 decimal places…

Q: A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced…

Q: For the beam shown, draw the shearing force and bending moment diagrams. Use area method. Show all…

Q: Which of the following statements is correct about the given structure? pin roller I fixed It is…

A: A fixed beam is given with intermediate roller and it has been asked to check the stability of the…

Q: 8 kN 8 kN -2 m- 2 m 3 kN/m Refer to the figure, what is the horizontal component of the reaction at…

A: Note: there is an internal hinge at B so, moment to the left and to the right of it both will be…

Q: Determine the MEMBER END MOMENTS AND REACTIONS for the beam shown below using the MOMENT…

Q: Do you think that the storage in sanitary landfills is the best way of disposing our solid wastes?…

Q: A compound curve connects three tangents having an azimuth of 240°, 270° and 280° respectively. The…

Q: The bro

A: Calculate the restrained elongation. Then using the formula for elongation the compressive load can…

Q: II. Using Center Line Method: 1. There're two rooms. Determine concrete in base (foundation),…

A: Given, Room dimension =3.5 m×4 m Width of earth work in excavation = 0.90 m Width of brickwork in…

Q: Using the method of joints, determine the force in each member of the truss shown below (solve for…

Q: Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the…

A: Option (C) is correct.

Q: 1. A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is…

Q: For a given sandy soil with maximum and minimum void ratios of 0.76 and 0.43 respectively has a…

Q: Given the space truss, find the force member AB in kN?

A: Solution-The given diagram is shown below, To Determine The force in member AB in kN

Q: The frame is made from pipe that is fixed connected. If it supports the loading shown, determine the…

Q: 8 kN 8 kN -2 m- m 2 m 3 kN/m D. -3 m Refer to the figure, what is the horizontal reaction of support…

Q: The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.34 in2. Find the…

Q: Which of the following gives the reaction at C in the given beam?

Q: 1) The beam is loaded as shown in the figure. Derive the shear and bending moment equations and draw…

A: Given, The given beam is a propped cantilever beam which is loaded with combination of Udl and…

Q: Defined and explain the procedures in plastering the masonry surface of a wall.

A: Plaster is defined as a thin layer of the mortar which was applied over the masonry surface and it…

Q: Consider a uniform 10m long beam, with flexural rigidity of 15,000NM2 Question 1: that is clamped on…

Q: This is a process of laying of stone masonry blocks in a wall in which the squared pieces of stones…

Q: A two-story office building has interior columns that are spaced at 6.71 m apart in two…

A: Reduced live load To account for the lesser likelihood that all levels above the column will be…

Q: 3. The following tabulated data is to be used in determining the area of traverse ABCDE by the DMD…

Q: 4) A trailer and truck combination having the axle loads as shown in the figure rolls across a…

Q: QUESTION 2 PROBLEM 2: Calculate the components of the forces at B and C. A D E F b Given: P= 21 kN a…

Q: For the beam shown in the figure below, draw the influence lines for Ra, Rc, Re, Vd and Md and…

A: Note: we experts are required to answer only first 3 sub parts of question. Please send the…

Q: The curve of a diversion road has a tangent “AB” which is directed due North and the other tangent…

Q: Adjust the traverse using the TRANSIT RULE. Determine the following: a) Sketch of the traverse b.…

Q: Which of the following statements is correct about the given structure? 4. A В C pin fixed roller…

A: Need to find out degree of indeterminacy

Q: The length of the spiral curve is 60m with a radius of 386.2m at the central curve. a. Determine the…

Q: Classify the trussshown as statically determinate, statically indeterminate, or unstable. If…

Q: what is the hotels estimate of no shows plus cancellations and early departures, which is determined…

A: There are different types of estimations done in the analysis. There are different factors of these…

Q: Determine the MEMBER END MOMENTS AND REACTIONS of the beam. USE: MOMENT DISTRIBUTION METHOD. 120 kN…

Q: Classify each of the structures as statically determinate, statically indeterminate, stable, or…

Q: Mechanics of Deformable Bodies Calculate the increase in stress for each segment of the compound bar…

Q: M (KN-m) 1,575 Draw the load and the shear force 601.5625 diagrams that correspond to the given…

Q: 14. Calculate the maximum moment

Q: Calculate the y-coordinate of the centroid of the shaded area. 12" 55°55 11" 2" 12" 12"- Answer: Y =…

Q: A circular plane with radius equal to 3 m is submerged in water with its top edge flushed on the…

A: Given data : Radius of circular plane r=3 m Unit weight of water γ=9.81 KN/m3 Vertical distance of…

Q: A trailer and truck combination having the axle loads as shown in the figure rolls across a simply…

Q: P1 =346 kPa D; =0.12 m P2 107 kPa D2 43 m

Q: If the pressure at the bottom of an open tank is 765 kPa, find the unit weight (kN/m) of gold in…

A: Given data: Unit weight of water = 9.81 kn/m^3 Unit weight aluminum=26.487 kn/m^3 Unit weight of…

Concept explainers

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.

Question

The rod ABC is made of an aluminum for which E = 71.5 GPa. Knowing that P = 6.32 kNand Q = 46.66 kN,determine the
deflection (in um) of point B if y = 0.44 and z = 0.51. Round off the final answer in four decimal places.
20-mm diameter
60-mm diameter

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross section of a slit rectangular tube ofconstant thickness is shown in the figures.(a) Derive the following formula for the distance efrom the centerline of the wall of the tube in thefigure part a to the shear center S: e = [b(2h+3b)/[2(h+3b)] (b) Find an expression for e if flanges with the samethickness as that of the tube are added as shownin figure part b.
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
the clamp exerts a normal force of 100N on the three pieces held together as shown. what force P may be exerted motion impends? the coefficient of friction between the pieces is .60
Solve this Portion Use problem 3.52. Add a force of 500 kN that is perpendicularly applied at point B in the direction from B towardC.Remove the torque.The steel and brass are assumed to have Poisson’s ratios of 0.30. (a)Determine the internalforce in AB.(b)Determine the internal force in BC.(c)Determine the deflection at Point B.(d)Determine thereaction at Point A.(e)Determine the reaction at Point C. Explain your work concisely and in detail
The system of knotted cords shown support the indicated weights. Compute the tensile force in cord A, using Jacobi's Method. Calculate in four decimal places and in 0% approximate error. The answer should be in lbs.
Determine the moment of Area of the given Built-up section about its centroidal axis.The top flange is 8” X 1”and the stem is 16” X 1” the bottom flange is 16” X 1.5” , the angle bars are 2- 5”X3”X ½. Tabulate your answer and complete solution.
the values are A = 3 , B = 4, C = 1, D = 0 please answer the forces
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of compression block of the section in PART B in mm.0
Vn = 6*36*1/(4*1.1) = 49.09 am I wrong? I believe in the calculation in the solution the coefficient m was not taken into account. And Pn is not 54 kips either, with the given formula it comes up as 6*36*0.5/(4*1.25) = 21.6 and in which case the design strength would be 21.6 kips. Please let me know if there's something I'm missing from the formulas.
And determine the x bar and y bar
Calculate the Member Force AB in Kips . Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the effective depth of the section in PART A in mm.0 Use 3 decimal places in all your computations except for strain and rho(5 decimal places).