The rubber mallet is used to drive a cylindrical plug into the wood member. If the impact force varies with time as shown in the plot, determine the magnitude of the linear impulse delivered by the mallet to the plug. Assume F1 = 174 N, t̟ = 0.003 s, t2 = 0.0125 s, t3 = 0.014 s. Amswer: Impulse = i N-s F, N

The rubber mallet is used to drive a cylindrical plug into the wood member. If the impact force varies with time as shown in the plot, determine the magnitude of the linear impulse delivered by the mallet to the plug. Assume F1 = 174 N, t̟ = 0.003 s, t2 = 0.0125 s, t3 = 0.014 s. Amswer: Impulse = i N-s F, N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.59P: How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull...

See similar textbooks

Similar questions

The L-shaped frame is made from two fixed-connected segments. Determine the horizontal displacement of the end C. Use the method of virtual work. EI is constant.
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
Please respond as reply as possible, USE THE DATA SHOWN IN THE TABLE. Distances are in centimeters The mechanism shown is used to carry out experimental tests on different industrial springs that are placed between the wall and point A. The rigid reinforcement that holds the spring at A moves through the horizontal beam by means of the 4 frictionless rollers. The piston CD is compressed by stretching the spring at A. For the situation in the position shown the spring is stretched a distance s and has an elongation constant of 2000N / m. The weight of the system can be considered negligible. Determine: 1.The magnitude of compressive force exerted by the piston at the position shown. 2.The magnitude of the force experienced by the bolt at E.
The driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800 N and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 K P
The driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800lb and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 kp.
When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed of = 20 ft>s. If the post is made of 2014-T6 aluminum and the spring has the stiffness of k = 250 kip>in., determine therequired minimum diameter d of the post to the nearest 1/8 in. so that it will not yield when it is struck by the block
If spring is found to extend 20mm for each 2kg of mass, the defelaction of spring carrying a mass of 10kg is A)200mm B)1m C)0.1m D)10m
If a spring is found to extend 30 mm for each 2 kg of mass, the deflection of the spring carrying a mass of 10 kg is Select one: 1.5 m 0.15 m 15 m 300 mm
Please respond as quickly as possible, USE THE DATA SHOWN IN THE TABLE. Distances are in centimeters The mechanism shown is used to carry out experimental tests on different industrial springs that are placed between the wall and point A. The rigid reinforcement that holds the spring at A moves through the horizontal beam by means of the 4 frictionless rollers. The piston CD is compressed by stretching the spring at A. For the situation in the position shown the spring is stretched a distance s and has an elongation constant of 2000N / m. The weight of the system can be considered negligible. Determine: 1.The magnitude of compressive force exerted by the piston at the position shown. 2.The magnitude of the force experienced by the bolt at E.
The journal bearings at A and B exert only x and z components of force on the shaft. Determine the shaft’s diameter to the nearest millimeter so that it can resist the loadings. Use the maximum distortion energy theory of failure with sallow = 200 MPa.
Determine R if the equivalent spring stiffness constant (keq) of the spring system is 500 N/m
The rod is pinned at its end A and attached to a torsional spring having a stiffness k, which measures the torque per radian of rotation of the spring. If a force P is always applied perpendicular to the end of the rod, determine the displacement of the force. EI is constant.