The section of 4*5 group pipe pile, each 15 m in long, embedded in clay layer, the diameter of pile = 403 mm. the center to center spacing of the piles is 700 mm. The clay layer properties, Cu = 60 kN/m2, saturated unit weight = 18.33 kN/m3 Solve the questions 5- 8. Find the empirical adhesion factor (a) * %3D %3D 0.92 0.82 0.74 0.62 None of the above

The section of 45 group pipe pile, each 15 m in long, embedded in clay layer, the diameter of pile = 403 mm. the center to center spacing of the piles is 700 mm. The clay layer properties, Cu = 60 kN/m2, saturated unit weight = 18.33 kN/m3 Solve the questions 5- 8. Find the empirical adhesion factor (a) %3D %3D 0.92 0.82 0.74 0.62 None of the above

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.10P

See similar textbooks

Similar questions

Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.For the sand, unit weight, γ = 17 kN/m3 and soil friction angle, ϕ’ = 35o. Estimate the ultimate point??? with each of the following:1.1 Meyerhof’s method (Ans: 1014 kN)1.2 Vesic’s method (Ans: 1754 kN)1.3 Coyle and Castello’s method (Ans: 2479 kN)
Please help me solve3.8 The soil profi le at a site for an offshore structure is shown in Figure P13.8. The height of the pile above the sand surface is 15 m. Determine the allowable load for a driven closed-ended pipe pile with diameter 1.25 m and embedded 10 m into the stiff clay. A factor of safety of 2 is required
A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.53 Nq = 99 Specific gravity, Gs= 2.61 Void ratio, e =1.21 Saturation above the GWT = 0.41 Ground water table (GWT) is located 3.58 m below the ground. Use unit weight of water = 9.81 kN/m3 Coefficient of friction = 0.41 Factor of safety = 3.98 Calculate the allowable capacity of the pile in kN.
A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The soil has the following properties: Dry unit eight is 18 kN/m3 and saturated unit weight is 21 kN/m3 (water table is 4m below from the ground surface), Nq=85, k=1.25, tan αα = 0.45 and FS=2.5 a) Calculate the end bearing capacity b) Calculate the frictional resistance c) Calculate the allowable load
A square prestressed concrete pile with a cross section 0.3 m by 0.3 m is driven 15 m into overconsolidated clays with properties as defined: From the ground surface to a depth of 7 m, the unit weight is 17 kN/m3 and the shear strength cohesion cu is 70 kPa; below 7 m, the soil unit weight is 18.5 kN/m3 and cohesion is 105 kPa. Use the total stress α-method to calculate both the design downward axial capacity and upward axial capacity, using a factor of safety of 3 (downward and upward).
The section of a 4 x 4 group pile in a layered saturated clay is shown in Figure P 9.29. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing (d) of the piles is 1 m. Determine the allowable load bearing capacity of the pile group. Use FS = 3 and Table 9.10.
A circular pile 0.65m in diameter and 13m long is embedded in loose sand. Site investigation suggests a dry unit weight of 17.35 kN/m3, moisture content of 9% above the water table, specific gravity = 2.65, and a saturated unit weight of 21.46 kN/m3 for the soils beneath the water table (2.75m below the surface). Nq = 95, k=1.35, tan α= 0.35 and FS = 3.0. Calculate the end bearing capacity Determine the skin friction capacity of the pile Find the allowable load if the factor of safety is 3.0 Please answer this asap. For upvote. Thank you
A 600mm diameter pile is embedded in 3 layers of dense sand at a depth of 17m. Nq = 86. The groundwater table is situated between Layers 2 and 3. The layers have the following properties: Layer 1: γ = 16.9 kN/m3. 3m thick. Layer 2: γ = 17.6 kN/m3. 5.5m thick. Layer 3: γsat = 19.65 kN/m3. K is 0.9 and tan α = 0.37. The factor of safety is 3.0. What is the skin friction resistance of the pile in kN? None of the choices 1684.170 1477.156 1257.150 1322.744 866.118 Please answer this asap. For upvote. Thank you vey much.
Determine the ultimate load capacity of a circular pile with diameter D = 20 cm installed in asaturated soft clay. The pile is embedded 10 m into the ground. According to measurements, thesoil exhibits an undrained shear strength according to the linear relationship: Su = 2+1.6z, wherez is the depth in meters and Su is the undrained shear strength in kPa. The soil's unit weight canbe assumed as 18 kN/m3
Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf = 3.5 m, and D (pile diameter) = 406 mm. The water table coincides with the top of the clay layer. Determine the total downward drag force on the pile. Assume ẟ' = 0.6 Φ'clay.