The section of a reinforced concrete T-beam has d= 500mm bf = 600mm t = 100mm bw = 300mm. The beam is reinforced with 12 pieces of 28mm diameter bars with Fy = 415 MPa. Concrete strength F'c = 28 MPa. Determine the Safe Ultimate Moment Capacity of the beam.

The section of a reinforced concrete T-beam has d= 500mm bf = 600mm t = 100mm bw = 300mm. The beam is reinforced with 12 pieces of 28mm diameter bars with Fy = 415 MPa. Concrete strength F'c = 28 MPa. Determine the Safe Ultimate Moment Capacity of the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Set P1 = 6.8 kN , P2 = 8 kN . Determine the force in the member AB, and state if the member is…

Q: The beam is constructed from four boards as shown. If it is subjected to a moment Mz = 16 kips-ft,…

A: Given Mz= 16 kips-ft Determine the stress at points A and B.

Q: Determine the maximum flexural stress on the beam in MPa.

A: Beam : A beam is a structural element which is used to resist the load of structure. A beam resists…

Q: The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel…

Q: A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 665 lb as shown. The…

A: The maximum bending stress in the pipe is calculated by using the following equation σmax = MyI…

Q: b) A rectangular beam 300 mm deep is simply supported over a span of 4 meters. Determine the…

A: To determine the intensity of the uniformly distributed load on the beam for the given allowable…

Q: The rigid beam ABC is supported by a pin at A and two wires BD and CE each with a cross section area…

A: The elongation is the deformation measurement that occurs before, the material breaks which the…

Q: 5 kN 2m 2.5 kN/m 1m 3m R₁ =10 kN The allowable flexural stress is 20 MPa for this beam. Determine…

A: Given data in question UDL Point load Span member length To find out Maximum moment Height h

Q: Q2. Referring to Figure Q2(a) until Figure Q2(c), check the stability and determinacy of the truss.…

Q: 2.) A beam has a T-section built up by two plates as follows: a 200 mm x 40 mm plate as flange and a…

A: Given data Flange size Width of flange (bf) = 200mm Thickness of flange (tf) = 40mm Thickness of…

Q: 60KN ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD Compute: Axial Load of AD 2 Moment at Support B…

Q: b h L Problem 1 164.0mm 335.0mm 3.70m Determine the Maximum Shear and Bending Stress of the…

Q: Determine the weight of 8m simply supported 200mm x 500mm rectangular beam whose allowable flexure…

A: Given data, Width of beam = 200 mm Depth of beam = 500 mm Stress in beam = 22 MPa. L = 8 m To find…

Q: W1 A 幸 10 ft 10 ft Set w1 (k/ft) A (1,2,3,4,5) B (6,7,8,9,0) 3. If the given beam has constant El,…

Q: 1) F=36 kN single load, M=48 kN.m moment and w=20 kN/m distributed load act on the beam whose…

Q: 604 2아시 KN A 4m Solve for the member force of member AC using method of joints indicate if its in…

Q: 5. An interior slab has dimensions 5m x 6m (measured center to center of supporting beams). Beam…

A: Solution: Total static moment in a panel: Mo=wul2ln28 Where; wu = factored load ln = clear span in…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

Q: 2. A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement…

A: 2.

Q: A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer…

Q: A steel tank 2m by 1.5m by 1.2m weighs 10KN when empty and is supported by two steel beams spanning…

A: Solution: Given: Weight of steel tank = 10 kN Weigth of the steel beam = 10 kN Weight after filing…

Q: Determine the uniform factored load each. Pn=270kN

A: P=270kN

Q: Determine

A: LENGTH OF BEAM (L) = 4 m width of section (b) = 2 inch depth of section (d) = 4 inch concentrated…

Q: A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be…

Q: 30 kN/m 8 m B 30 kN

A: To find the internal force in members-

Q: the given section of beam is at point of maximum moment of the beam loaded shown. use n=8 ,…

Q: 21 Figure 1 shows a continuous beam fixed at A and has simple supports at C and E. Using the static…

A: Given data in question Beam Span length Loading To find out Ds No. Of plastic hinges locations…

Q: 4. Consider the angle iron. If the moment acting on the cross section is 936 kip-ft, determine the…

A: Answer To calculate the Maximum compressive stress and Maximum tensile stress we can use the Bending…

Q: moment acting on the cross section is 15 kN.m, determine the stress at points A and B and show the…

Q: ation 4. The following are the properties of a rectangular beam reinforced with tension only having…

Q: Problem 2: If P=8 kips, determine the force in each member. Identify whether the force is in tension…

Q: 6-78. The steel beam has the cross-sectional area shown. If w 5 kip/ft, determine the absolute…

A: *Ans: w=5 k/ft ∑11 Fy=0 :RA+RD=582 RA +RD =80K

Q: Solve the given truss below if L36.4m and F=420 kN L L L- B D E G. 3.6 m H. A J K M F F F F…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A: P=500kN To find thickness of steel pipe and radius of base plate

Q: 1. Determine the resultant internal loadings in the beam at cross sections through points D and E.…

A: Given :

Q: - Determine the Maximum Bending stress at ainy location alang the beam? futo 500 700 N/m 200 30…

A: ASKED: To determine the maximum bending stress in the beam with given cross-section. The maximum…

Q: .3 The torque of 100 kip - ft produces a maximum shear stress of 8000 psi in 6-ft-long hollow steel…

Q: Compute the maximum bending moment of the given beam below. (kN-m) Note: Use two (2) decimal places…

A: Maximum Bending moment will be at the point where the shear force value is zero.Consider the below…

Q: Determine the maximum flexural stress of the beam shown.

A: To calculate the maximum flexural stress in the given beam. Given, Width of beam, b = 75 mm Depth…

Q: G H -67.5 kN 3.6 m -112.5 kN E F 3.6 m 6 m -4.5 m- Use portal method to analyze the frame. Determine…

Q: Compute the maximum bending moment of the given beam below. (kN-m) Note: Use two (2) decimal places…

Q: If the length of strut is 1.5 m and axial load P = 23 kN with w = 2.5 kN/m, calculate maximum…

A: Question is based on the uniform strut whose both ends are hinged. Length of strut,Load on strut,…

Q: For the cantilever steel beam [E = 210 GPa; I = 145 × 106 mn Assume L = 1.6 m, P = 56 kN, and w= 32…

Q: Determine the weight of 10m simply supported 200mm x 500mm rectangular beam whose allowable flexure…

Q: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). Ⓡ…

A: Given Data: Total load=P=890 kN Factor of safety=3 Thickness of cross-section=10 mm Ultimate…

Q: a) Calculate supportive reactions. b) Determine the shear equations, V(x), and the bending moment,…

A: Given:- A beam is given with a point load and moment The value of H = 83 The magnitude of the…

Q: *6-101. The steel beam has the cross-sectional area shown. If we- 2 kip/ft, determine the maximum…

A: *Ans: wo=2k/ft Max. Bending stress σm=? ∑11Fy=0 RA+RB=12×18×12

Q: 4. A solid rectangular section beam, with cross-section 0.01m × 0.02m, and length 1m is simply…

Q: he timber member BC, inclined at angle 0 = 60° to the vertical, is supported by a pin at B and the…

A: Given a timber member BC, inclined at angle 0 = 60° to the vertical, is supported by a pin at B and…

Q: A beam ABC with an overhang from B to C is constructed of a C 10 x 30 channel section with flanges…

Question

100%

The section of a reinforced concrete T-beam has

d= 500mm

bf = 600mm

t = 100mm

bw = 300mm.

The beam is reinforced with 12 pieces of 28mm diameter bars with

Fy = 415 MPa.

Concrete strength F'c = 28 MPa. Determine the Safe Ultimate Moment Capacity of the beam.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Interpretation of data

VIEW

Step 2 Primary calculations

VIEW

Step 3 Calcultion for moment capacity

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 19 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the ultimate moment capacity in kN∙m of the beam in negative bending. 42.79 40.56 47.55 45.07
Use cantilver method Calculate for the axial force in kN at member CB a = 40.4 kN, b = 21.7 kN, c = 3.6 m
Question 34 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in positive bending. Write the answer in 2 decimal places only.
2.) A beam has a T-section built up by two plates as follows: a 200 mm x 40 mm plate as flange and a 100 mm x 20 mm plate as web. The maximum shear force acting on the beam is 60 kN. a) Determine the moment of inertia of the section about the neutral axis, in mm4. b) Determine the shear stress at the neutral axis, in MPa. c) Determine the shear stress on the web at the junction of the flange and the web, in MPa.
Determine the force in member AC using stiffness method. Take A =0.75 in² and E =29 (10³) ksi.
determine the maximum bending moment (kN-m) ASAP plss
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
Calculate for the axial force in kN at member CB using cantilever method a = 40.4 kN, b = 21.7 kN, c = 3.6 m
A simply supported beam AB = 9 m has a hollow rectangular cross-section with 13 cm as width, 20 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 8 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 2 m. note; sole 4 . 5.6 and 7 i) Reaction force at B in (N)= ii) Reaction Force at A in(N)= iii) The distance from B at which the shear Force value changes from "-" to "+" in (m)= iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 1 cm from the top in (N/m^2) =
Determine the crippling load for the “T”section of length 5m when it is used as a strut with both ends hinged. E=2.0x105 N/mm2
The steel beam has the cross-sectional area shown. If w = 5.2 kip/ft, determine the absolute maximum bending stress in the beam where: L1= 6 ft; L2 = 9 ft; bf = 8.5 in; and tw = 0.3 in
6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.