The shaft shown below is made of AISI 1020 steel. Determine the most critical section, the principal stresses at the groove and at the fillet. Assume no concentration factors at the wall. The dimensions of the various diameters shown are d = 30 mm, D = 45 mm, and d2 = 40 mm. 40 mm. 7= 9mm D 40 mm 6 mm 1 kN 40 mm 10 kN T = 50 N-m

The shaft shown below is made of AISI 1020 steel. Determine the most critical section, the principal stresses at the groove and at the fillet. Assume no concentration factors at the wall. The dimensions of the various diameters shown are d = 30 mm, D = 45 mm, and d2 = 40 mm. 40 mm. 7= 9mm D 40 mm 6 mm 1 kN 40 mm 10 kN T = 50 N-m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
A composite shaft consists of 3 cylinders that are made from aluminum, copper and steel. Multiple axial loads are applied. The radii and Elastic Moduli of the cylinders are given. Neglect the size of collars B and C. F₁ Aluminum Eal r1 F₁ F₂ F3 FA d₁ d₂ d3 F₂ H F₂ B d₁ Copper Ecu r2 T1 72 T3 Ealuminum Ecopper Esteel Value C 1.75 KN 5.75 KN 2 KN 5.75 KN 0.5 m 0.2 m 0.3 m 0.16 m 0.28 m 0.12 m 74 GPa 112 GPa 202 GPa Steel Est [3 d3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable F₂ F₂ D F₁ a. Determine the normal stress in section AB, OAB. b. Determine the normal stress in section BC, OBC. c. Determine the normal stress in section CD, gcn.
1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b Ay r r=2acose Figure 1: Circular shaft with a keyway. The keyway is represented by the boundary equation r = b and the shaft is represented by the boundary equation r = 2a cos 0. Show that using a Prandtl stress function of the form ²) (₁ (1-2a cos) X v = K (b² − ²) (1 – : will solve the problem of torsion on this shaft and find the constant K (assume an applied torque T). Compute the shear stress components Txz and Tyz. (Hint: start by converting the stress function to Cartesian coordinates).
Problem 2: For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 02 and, 03) using Mohr's circle. r= 0.0042 m, d = 0.03 m, D = 0.033 m, T= 250 Nm P = 1500 N, M = 300 Nm, A M T J.C₁ P r M T Di d
The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum longitudinal stress caused by an internal pressure of 1.2MPA if the steel plate has a thickness of 10mm. b. Determine the maximum circumferential stress caused by an internal pressure of 1.2MPA, if the stress plate has a thickness of 10mm. c. Determine the minimum thickness plate which maybe used if the stress is limited to 40MPA and the internal pressure is 1.5MPA. 1400 mm 400 mm 600 mm
At a point in a component, the state of stress is shown on the element below. Assume that the stress magnitudes are sy- 8544 psi and Sy = 4835 psi. The stresses act in the directions indicated in the figure. Determine the magnitude of the absolute maximum shear stress that acts at the point. Answer: Tmax=i psi %3D
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
The tank of the air compressor is subjected to an internal pressure of 0.43 MPa as shown in (Figure 1). The internal diameter of the tank is 550 mm, and the wall thickness is 6 mm. Figure ⁹-1 Y Y Part A Determine the hoop stress acting at point A. Express your answer to three significant figures and include the appropriate units. 0 = Submit Part B 02 = Submit O Provide Feedback HA Value Request Answer Determine the longitudinal stress acting at point A. Express your answer to three significant figures and include the appropriate units. Value HÅ 1 h Units Request Answer Units ? F ?
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, Px = 20 kN, P, = 16 kN, and P, = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a |P, y P: P H K
Derive the relationship between critical resolved shear stress and disloca- tion density given below Terss = To + AVPD