The shear diagram of a simple beam is given. Assume there are no applied moments along the beam. Write your answer in UPPERCASE. If the answer is not among the choices, write X What among the following best represents the load between points C & D? Answer: 15 kN/m А. B. 30 kN/m 40 V (kN) A -25 1m C. D. B 35 3 m 30 -40 C 2 m 15 kN/m 30 kN/m D E. F. 15 kN/m 30 kN/m

The shear diagram of a simple beam is given. Assume there are no applied moments along the beam. Write your answer in UPPERCASE. If the answer is not among the choices, write X What among the following best represents the load between points C & D? Answer: 15 kN/m А. B. 30 kN/m 40 V (kN) A -25 1m C. D. B 35 3 m 30 -40 C 2 m 15 kN/m 30 kN/m D E. F. 15 kN/m 30 kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the Shear and Moment Diagram in the beam shown below by AREA METHOD. Show the complete area of the curve as your solution. Use the dimension of the beam in meters. The unknown concentrated load corresponds to the summation of the GIVEN NAME & FAMILY NAME below. Given Name: Samantha Barnadete Family Name: Mindoza So the unknown concentrated load is 24.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and CAssume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15If there is a settlement of S at the support C, solve the following using slope deflection method:
Using virtual work method, find: (a) the real internal force F in member BF in kN (b) real internal force F in member GH in kN (c) virtual internal force Fv in member HG due to a one unit horizontal load applied at joint G (d) virtual internal force Fv in member CD due to a one unit horizontal load applied at joint G (e) horizontal displacement at joint G due to the applied loads in mm. Given: a=25kN b=22kN c=4km
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determinethe safe compressive load. (Figure below)adding a cover plate on the figure of the same size at the bottom, compute the centroidal moment of inertia about x and y axes
Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa. Round off to two decimal places a. Vertical Reaction at C in kN.b. Slope of the elastic curve at support C in degrees.c. Deflection at point B in mm.d. Deflection at point D in mm. Show organized solutions
F=30 kN single load, M=34 kN.m moment and w=10 kN/m distributed load are acting on the beam whose loading condition is given in the figure. Point B is located just to the right of the application point of force F and moment M. The length L is also given as L=5 m. According to this;Question1-A) Find the support response (Dy) at point D. (Write your result in kN.)Question1-B) Find the support response (Ay) at point A. (Write your result in kN.)Question1-C) Find the shear force (VB) at point B. (Write your result in kN.)
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
(G) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of Joint B and Point D. ANSWERS in inch (H) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship between the force in rod 3 (F3) and the applied load, P. (I) Based on the allowable stress for the bronze, calculate the maximum allowable force that can be supported by rod (1), and the corresponding maximum value for the applied load P. IN KIPS (J) Based on the allowable stress for the aluminum, calculate the maximum allowable force that can be supported by rod (2) and rod 3, and the corresponding maximum value for the applied load P. IN KIPS (K) Using the results from Part 8, determine the deflections of Joint B and Point D. IN INCH NOTE: These are the…
Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
Write the shear and moment equations for the beam shown. Draw the shear and moment diagrams under the load diagram. SOLVE FOR SEGMENT AB, BC, CD, DE. DERIVE THE SHEAR VALUE 27 FT. TO THE RIGHT OF POINT E IN SEGMENT EF. DERIVE THE MOMENT VALUE 27 FT TO THE RIGHT OF POINT E IN SEGMENT EF. Show FBD. F1 = 10 lb F2 = 30 lb/ft F3 = 21 lb/ft