The shorter leg of two 6" x 4" x 1/2 angles are welded to a 12" - 20.7 lb channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel and perpendicular to the web of the channel

Q: Exercise 2: Calculate deflection at B and slope at A. 500 N/m C 4m B 5- 200 G 4 m 10x10 cm 2

A:

Q: The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90…

A:

Q: All are methods of determining the bar force of a truss member except one. Which one? Maxwell…

A: Method of virtual work is not method of determining the bar force of truss member instead it is…

Q: find all reaction for the frame by the force method

A: Let's take Hc as redundant  Using Theorem of least work (Force Method)

Q: ELEV. = ?? A L=600m D = 35cm ELEV. = 10 D Assuming that all pipes has a friction factor of 0.021,…

A:

Q: Problem 2 A w1 w2 31.3kN/m 40.7kN/m w1 6.2m 8777 w2 4.8m

A:

Q: Use the three moment equation to determine the moment over the support of the following beams and…

A:

Q: Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and…

A:

Q: For the given state of stress of element A, strictly using Mohr's Circle perform the following:…

A:

Q: A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the…

A:

Q: If 2340 vehicles pass a certain lane of road with an average speed of 52 kph, determine the…

A:

Q: find the horizontal force at support "A" by force deflection method

A:

Q: A solid having a specific gravity of 3.5 is floating on a liquid having a specific gravity of 13.6.…

A:

Q: Write all the commands steps of the AutoCAD software to reach the object shown in the figure below…

A: To Determine Commands and steps to be used to reach the object shown in the figure in AutoCAD.

Q: 5. Determine the reactions at A and B for the loaded beams. Beam wei 1m 4 m 3m 5 m 12 kN/m B

A:

Q: Use the three moment equation to determine the moment over the support of the following beams and…

A:

Q: MN/m². 1005. A timber beam 150 mm by 250 mm is reinforced at the bottom only by a steel plate, as…

A: Determine the concentrated load that can be applied?

Q: The soil material is supported by a retaining wall to a height of 6m. The unit weight of soil is 16…

A:

Q: Determine the slope at A and displacement at C. El is constant.

A: Determination of slope At A and Displacement at C### using ##

Q: A block is pushed against a horizontal spring, compressing it to 22 cm. After being released, the…

A:

Q: Compute the uplift force in KN per meter

A:

Q: A block of wood with length "h" and cross-sectional area "A" is submerged in water with 50mm exposed…

A:

Q: 3 A circular curve of radius 250 m is to be inserted between two straight meeting at a deflection…

A:

Q: A wall of 5 m height retains a backfill of dry granular soil that has a level surface and weighs 20…

A:

Q: In determining the elevation of point A and the distance between two points, A and B, a theodolite…

A:

Q: a laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a…

A:

Q: FA: 300 lb Weight of forklift: 2,000 lb Weight of load: 900 lb Wheels at B are free to roll.…

A:

Q: A soil profile consisting of three soil layers is shown. Characteristics of the layers are: Layer…

A: To find effective stress at point c

Q: 2230 kN 80 mm 1.75 m X 90 mm Z 2230 kN Y

A:

Q: rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3…

A:

Q: Example 10.6 An embankment is to be formed with its centre line on the surface (in the form of a…

A: Calculating A1 First let us find the area of the triangle on the sides of the embankment in A1. By…

Q: 6-0 Water > Sand -22 h₁ h₂ A: 0⁰⁰⁰ 8 J 0⁰⁰

A:

Q: steel section. Check web yielding and web crippling if the steel used is ASTM A992, grade 50.

A: Solution: For W18×50, we obtain the following properties from ASTM, Below are the structural steel…

Q: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s A 0 4 ft B…

A:

Q: A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the…

A:

Q: Solve the given problems. 4. Determine the x, y, z components of reaction at the ball-and-socket…

A:

Q: Manny Pacquiao owns a hydraulic press for his training to box in the presidential race. It is filled…

A: Given, Relative density = 0.82

Q: L = 6000 ft D = 18 in L = 2000 ft D = 12 in B

A:

Q: SITUATION. The turnbuckle is tightened until the tension in cable AB is 2.4 kN, as shown be 2 1.6 m…

A:

Q: لكلم L/2 • 1/2 B

A:

Q: A rectangular reinforced concrete beam has a width of 350 mm and an effective depth of 600 mm. The…

A:

Q: Q2/For the beam shown in Fig. (3). Determine the OB and Ap by double - integration method. 25KN/m…

A:

Q: Given the properties and elevations of the three reservoirs, if friction factor f, is 0.01 for all…

A:

Q: The shear capacity v if a steel wide flange section, 600 mm deep whose web is 9 mm thick, is closest…

A:

Q: A steel shaft 3 ft long that has a diameter of 4 in is subjected to a torque of 15 kip ft. Determine…

A:

Q: find the eccentricity and identify the type of conic;

A: Polar equation: - It is defined as an equation which describes the relation between distance from…

Q: Volumetric stain is the:   change in volume per unit time   square root of difference of original…

A:

Q: A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25 mm and a web…

A:

Q: O Y 3 in I. Compute the centroidal distance with respect to x- and y- axis of the figures below. 4…

A:

Q: In the bolt connection shown in the figure, 215 KN 30° 品 Os a. 189.3333 b. 174.6667 c. 183.3333 d.…

A: X-axis reference line pass through bolt 1-2-3 and Y-axis reference line pass through 1-6-11 bolt.