The simply supported beam is built up from three boards by nailing them together as A, shown. Determine the L1 L2 maximum allowable bf spacing s of the nails to support that load, if each nail can resist a tf tw shear force of V kN. hw tf P=17KN V=2kN L1=3.1m L2=2.5m bf=120mm tf=20mm hw=270mm tw=15mm

The simply supported beam is built up from three boards by nailing them together as A, shown. Determine the L1 L2 maximum allowable bf spacing s of the nails to support that load, if each nail can resist a tf tw shear force of V kN. hw tf P=17KN V=2kN L1=3.1m L2=2.5m bf=120mm tf=20mm hw=270mm tw=15mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.8P: Determine the allowable axial load Pallowfor a steel pipe column with pinned ends having an outside...

See similar textbooks

Similar questions

The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. If the wire has a diameter of 0.25 in., determine how much it stretches when a load of P = 600 lb acts on the pipe.
Assume that the wood column is pinned top and bottom for movement about the x-y axis, and ixed at the bottom and free at the top for movement about the y-y axis. Determine the maximum eccentric load P that canbe applied without causing the column to buckle or yield. Ew = 1.8(103) ksi, sY = 8 ksi.
The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5 mm and 2 mm, respectively. If the cables have a normal ultimate stress of ?u = 400 ???. Determine: a) The safety factor in cable AB b) The safety factor in cable BC Please add the free body diagram.
the pipe AB is screwed in tightly to a pipe flange attached to the wall. It has two forces acting on it as shown below. Draw a complete FBD of the bar (its loads and support reactions). FB= (2i + 6j + 3k) kNFc= (1i - 2j + 2k) kN
Prior to the application of the P = 120 kip load, the gap between C and the rigid wall at D was as depicted as below. Determine the support reaction at D (in kip) after force P has been applied. The assembly is made of solid cylinders: AB is Stainless 304 steel alloy, and BC is 6061-T6 aluminum alloy.
Determine the allowable axial load Pallowfor a steel pipe column with pinned ends having an outside diameter of 220 mm and wall thickness of 12 mm for each oft he fol lowing lengths: L =2.5 m, 5 m, 75 m, and 10 m. (Assume E = 200 GPa and y = 250 MPa.)
The strut is supported by a pin at C and an A-36 steel (Young’s Modulus is 200 GPa) guy wire AB. If the wire has a diameter of 5 mm, determine how much it stretches when the distributed load acts on the strut. W0=11Kn/m
Determine the maximum allowable load P that can be safely supported by the frame if t = 1.25 in. and b = 3.5 in. The wood has normal failure stress of sfail = 6 ksi, and a shear failure stress of tfail = 1.5 ksi. Use a factor of safetyagainst failure of 2.
The 304 stainless steel post A is surrounded by a red brass C83400 tube B. Both rest on the rigid surface. If a force of 25 kN is applied to the rigid cap, determine the required diameter d of the steel post so that the load is shared equally between the post and tube. The elastic modulus for brass is 101 GPa and the elastic modulus for steel is 193 GPa
A 20-ft-long column is made of aluminum alloy 2014-T6. If it is pinned at its top and bottom, and a compressive load P is applied at point A, determine the maximum allowable magnitude of P using the equations of Sec. 13.6 and the interaction formula with (sb)allow = 20 ksi.
The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of 0.2 in., determine how much it stretches when a distributed load of w = 100 lb>ft acts on the beam. The material remains elastic.
The truss consists of three members, each made from A-36 steel and having a cross-sectional area of 0.75 in2. Determine the greatest load P that can be applied so that the roller support at B is not displaced more than 0.03 in.