The size of a hole is designated as DE on the drawing. The actual size of the hole got more than D+ ES. What should be considered the hole?

Q: How much machining tin 58 mm over a length of approach length and ow

A: Machining Time

Q: the angle

A: Given: To determine: Angle theta before rotation

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: The height (in m)

A: Given data; A ball of mass 0.1 kg, initially at rest Ball dropped from height of 1 m.Ball impact…

Q: For the first question I just need the explanation of neutral dwell not the steps on how to set i

A: Dwell time for ignition systems refers to the period of time that the coil is turned on. During this…

Q: Sheet No.2 1- Write a program to find the average of 50 numbers and print the result.

A: Question (1) is Solved here. For Other Question, please Post again.

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: difference between points (1) and (2)?

A: the pressure difference = 9790X(133100/9790-1)*0.12 =14797.2 Pa =14.79 kPa

Q: se natural freque or separately is 10

A:

Q: A=pi r^2, you forgot to divide the diameter by 2 before plugging it in

A:

Q: the value of a

A:

Q: please solve fast. Explain Method of Sections in details.

A: Given: Explain Method of Sections in details.

Q: Find the centrc

A:

Q: ) Solve for total 5) Solve for the le the water surfa c) What is the ma solved total hy

A: Given

Q: THE FOLLOWING, MAKE SURE IT IS

A: Given,  h= 30 m  Pb = 101.001 kPa  Specific gravity = 1.03

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: solve for the direction and put a conclusion after getting the answer. Make sure that the answers

A: Resultant load is equal to the area under the curve Resultant load pass through CG of load

Q: Find the reorder point to achieve

A: Given;   Company uses 2555 units of an item annually.Delivery lead time , T=8 days

Q: Add Top

A: Only one question is allowed to solve.

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Can you put all the measurements, as in all measurements and make it in centimeters?

A: given : Isometric view

Q: A piece of frame material is 50’ long.  If we cut it into 6. 25" long pieces, how many pieces will…

A:

Q: ind the angle between A a

A:

Q: Please show all work and answers. If not ALL then please answer ones in RED. Thank you.

A:

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: how did you get 0.7967

A: The power output of the turbine is 0.80208 H.P.

Q: 10. How much runout is allowed on the Ø.8750 hole? 11. How deep is the Ø.8750 hole?

A: 10. How much run out is allowed on 0.8750 hole

Q: What is the height if the dimension figures written on the dimension line? a) 7mm to 9mm b) 2mm to…

A: Answer: d Explanation:          It is customary to write the figures with a height of 3mm to 5mm.

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: in figure, the length of wire

A: GIVEN:

Q: Find: (a) Find the value of Yo

A: For solution refer below images.

Q: The final answer should be in three decimal places.

A:

Q: em 3. A 400 Lb. n is 0 40 Doter

A: given:W=400lbμ=0.40θ=400

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate…

Q: Two 12' bars are cut into pieces 8-3/8" long and the saw kerf is 1/8" (waste). How many pieces can…

A: Given Data:- Length of each bar, L=12’

Q: 50 MPa

A: The Mohr’s circle is used to determine the principal stresses, normal and shear stress at various…

Q: How many even numbers of 3 digits can be made with the digits 0,2,3,5,7,8,9 if no digit is repeated

A:

Q: please label the parts

A: 2. a) The key differences between SI and CI engine are SI ENGINE CI ENGINE 1. Air & Fuel…

Q: How did 6650 mm2 come from please show the work.

A:

Q: What size hole was drilled in part? Would it be 3/16?

A: Solution:

Q: 1 The basic drilling process is that a at the bottom of_ grinds a hole through the rock layers.

A: The basic drilling process is that a drill bit at the bottom of rotating bit holder grinds through…

Q: what is "p"? in the work formula

A: ρ = Density of water in kg/m3 ρ = 1000 kg/m3

Q: a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm…

A: According to the details provided in the question, we need to DRAW the figure.  i am using the…

Q: so 0 is the answer?

A: