The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are as follows: Saturated weight is 19 kN/m^3. Friction angle is 19 degrees Cohesion is 20 kN/m^2. Unit weight of water is 10 kN/m^3 Limiting depth of slope is (m) 8.20 m 2.96 m 5.47 m 4.95 m

The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are as follows: Saturated weight is 19 kN/m^3. Friction angle is 19 degrees Cohesion is 20 kN/m^2. Unit weight of water is 10 kN/m^3 Limiting depth of slope is (m) 8.20 m 2.96 m 5.47 m 4.95 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.4P

See similar textbooks

Related questions

Q: A column 9m is fixed at the base about both axes and pinned at the top about both axes. In addition,...

Q: 8. At what distance a should the bearing supports at A and B be placed so that the deflection at the...

Q: Tacarigua aquifer in Trinidad is a medium to coarse grained sand aquifer. It is 12.19 thick and 1.61...

Q: A 200 MPa shear stress is applied on along CD. Calculate diagonal strain along AC. Given modulus of ...

Q: Determine and explain thoroughly, a. the equations of the shear and bending moment curves for the be...

A: According to company guidelines, we are allowed to answer only first 3 sub part of the question. For...

Q: . Construct the shear and moment equations of the loaded beam as shown and draw the shear and moment...

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other ques...

Q: Determine pinned support reaction

A: Given data : The value of Point load P=3 KN The value of Point load Q=22 KN The value of Point load ...

Q: Use Virtual Work Method to answer the questions below considering the truss shown in the figure. Ass...

Q: The value of moment generated at guided roller support C due to a concentrated point load of 10 kN a...

Q: Assume that taal lake is 100m2 and its average height is 5ft. Wastewater that flows into the lake ar...

A: Given Data : area of taal lake A= 100 m2 actual depth = 5 ft

Q: Activity 1: A rectangular piece of wood, 50 mm x 100 mm in cross-section is used as a compression bl...

Q: A catchment of area 200 ha has a runoff coefficient 0.5. A storm of duration larger than the time of...

Q: Note: this is not a graded question please help us to understand how to solve this sample question t...

A: To find force in member bd

Q: Determine the value of the maximum deflection and rotation at both ends for the beam loading shown. ...

Q: orizontally, not vertically. For this to work, there needs to be a resisting force, F, that holds th...

A: Diameter of jet(d)=81mm Velocity of water through jet(V)=23m/s To find force required to hold the pl...

Q: 10 m KN 15 KN/m

A: Given : A beam of 6 m length as shown below Required: To determine shear and bending moment at ever...

Q: storey residential project, make a logical arrangement of activities by filling out the column for P...

A: Step: 1 Critical path method (CPM): - It is defined as the longest path or shortest duration in whi...

Q: a tri-axial test of silty soil, the sample failed at normal stresses of 521 kPa and a shear stress o...

Q: Determine the force in the member AC for the given truss is 4 m 2.5 m 2.5 m G 2.5 m F 2.5 m 10 kN A.

Q: The uniform 15-m pole has a mass of 175 kg and is supported by its smooth ends against the vertical ...

Q: (a) Determine the reactions at A and E if P = 800 N. The reactions are positive if to the right or u...

Q: Еxample 5. In Line AE AN Quad. Calculated bearing Azimuth tan-1(A E/ AN AB 110 170 AC 200 -120 AD -1...

A: To find out the quadrant, bearing and azimuth of the traverse.

Q: Determine the maximum uniformly distributed load that can be loaded for the beam shown if the allowa...

Q: There are two identical groundwater pump facilities that is operating 6 kilometers apart. The hydrau...

Q: Use the slope-deflection method to analyze the contimuous beam shown in the Figure below. Draw the a...

Q: 2. (a) A well in an aquifer is pumped over a long period at a rate of 0.05 m3 /s under approximate s...

Q: 2. Find the pressure difference between A and B. AIR • B 180mm 45 H20 540mm 350 mm 200 mm

A: As per guidelines we need to answer only first question so please repost rest questions separately.

Q: Note: this is not a graded question please help us to understand how to solve this sample question t...

A: To find force in member ab

Q: For the truss given below, what is the restraint that can not be remove to arrive with a primary str...

Q: This is a determinate structure, which must be statically stable and used in the analysis of MCD?

A: Q1 Ans: Primary structure:

Q: Determine the maximum shearing stress and bending stress for the beam loading shown. Box your answer...

Q: The porosity of a sample of saturated sand in the loose state was 50%. Find the critical hydraulic g...

A: Given data : Porosity (n%)=50 Specific gravity of soil (GS)=2.6 To find : Critical hydraulic gradi...

Q: A drop hammer is used to drive a wooden pile. The hammer weight is 30 kN and its free falling height...

A: Given data,For drop hammer is used to drive a wooden pileWeight of hammer=30 kNFalling height =0.9 m...

Q: 1. yeza dx Evaluate the following differential equations by method of variable separable. Show your ...

Q: Assume that a residential area has a water pipe leaking continuously at the rate of 1.5 litres/sec. ...

Q: A concrete pile of size 50 cm x 50 cm is to be provided in a clay stratum vhose unconfined compressi...

A: Size = o.4mx0.4m load = 450 UCS unconfined compressive strength = 110kpa Hence c = 110/2 = 55 Adhe...

Q: 1. The bar AB with cross section Ag is shown in the figure, the strength condition is just satisfied...

Q: Compute the total deformation of bar ABC with a thickness of 12 mm. Use E = 30 GPa. в A -30 KN 40 KN...

Q: cal stress at point A located z = 5 m below urface. Given: x = 5 m. Please have the er in four (4) d...

Q: A loose, uncompacted sand fill 6 ft in depth has a relative density of 40%. Laboratory tests indicat...

Q: 4000 mm2 150 kN 3 m 4000 mm2 2600 mm2 B 4000 mm2 225 k 3 m- - 3 m- E= 70 GPa Determine the total dis...

Q: Highway functional classification: procedure

A: A primary objective of the functional classification system is to connect the traffic generators (po...

Q: Use Virtual Work Method to answer the questions below considering th shown. Use the cross-sectional ...

A: To find force in member ad

Q: Use Virtual Work Method to solve for the vertical deflection at the D in mm below. Put (-) negative ...

Q: PROBLEM 1 - A closed cylindrical tank 400 mm in diameter and 2.5 mm subjected to an axial compressiv...

Q: the support reaction

A: Given:- 10kN load To find:- support reactions

Q: A 900 mm diameter pipe 1,800 m long carries 1.2 cu.m./sec from reservoir A, whose water surface is a...

Q: Trials Angle (deg) R (m) Y max (m) Time (s) 1 25° 25.99 m 1.59 s 2 30° 28.60 m 1.8...

A: INTRODUCTION: This question deals with projectile motion of a particle. range of particle, R= u2sin2...

Q: PROBLEM No. 3 The degree of saturation of a soil is 55% and the moist unit weight is 16.75 kN/m³. Wh...

Q: Part A In (Figure 1), r = 30 mm Locate the centroid z of the metal cross section. Neglect the thickn...

Question

The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are as follows:
Saturated weight is 19 kN/m^3.
Friction angle is 19 degrees
Cohesion is 20 kN/m^2.
Unit weight of water is 10 kN/m^3
Limiting depth of slope is (m)
8.20 m
2.96 m
5.47 m
4.95 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A long slope is made up of a cohesionless soil with the internal friction angle of 34°. If the water table rises to the surface of the slope, then determine the maximum possible value of the slope angle to get a factor of safety of 1.5. Take saturated unit weight as 18 kN/m3 and the unit weight of water as 10 kN/m3.
Figure 15.47 shows an infinite slope with H = 9.14 m and the groundwater table coinciding with the ground surface. If there is seepage through the soil, determine the factor of safety against sliding along the plane AB. The soil properties are Gs = 2.7, e = 0.8, β = 16°, ϕ′ = 21°, and c′ = 59.8 kN/m2.
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the stability factor?
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
A 45° slope as shown in figure has been excavated to a depth of 6 m in a saturated clay having the following properties Cu= 50 kN/m², qu=0° and y = 19 kN/m³ Determine the factor of safety. [Take area of wedge = 39 m²]
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface.
Q.5 Figure 5 shows an infinite slope with H = 30 ft and the groundwater table coinciding with the ground surface. If there is seepage through the soil, determine the factor of safety against sliding along the plane AB. The soil properties are Gs = 2.7, e = 0.8, β = 16 ͦ, Ø = 21 ͦ, and c’ = 1250 lb/ft2 .
A 9m cut slope is shown in the figure. The unit weight of soil is 17kN/m3. Friction angle and cohesion along the rock surface are 20 degrees and 24kPa respectively. The slope makes an angle of 300 from horizontal and the failure plane is at 150. Determine the developed frictional force on the failure plane.
An infinite slope in purely cohesive soil has a saturated unit weight of 20 kN/m^3 and effective cohesion of 48 kPa. It has a slope of 18 degree. The clay has a depth of 5m over ledge rock. Depth of clay is measured vertically. 1. Determine the FS against slippage. 2. Determine the critical depth. 3. Compute for the stability number.
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
A cut slope is planned in a soil having properties as follows: γ = 19.3 kN/m3, ϕ′ = 19°, and c′ = 55 kN/m2. The cut slope makes an angle 60° with the horizontal. Assuming a planar failure surface, what would be the maximum permissible slope height, H, if the desired factor of safety is 2.5?
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?