Please answer Mo and provide the answer in 3 significant figures. 0.00i + 34.2j + 9.09k is incorrect. Thank you! The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For theconfiguration shown, where the wrench lies in a vertical plane and a horizontal 160-N force F is applied at A perpendicular to thehandle, calculate the moment Mo applied to the bolt at O. For what value of the distance d' would the z-component of Mo be zero?Assume a = 85 mm, d = 150 mm, h=165 mm, 0 = 19⁰AnswersMo (i+i34.2i 9.09k) N-md= 89.81.00mm

The given force in vector is The position vector of the force can be determined as shown below.

The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench Illes in a vertical plane and a horizontal 160-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the 2-component of Mo be zero? Assume a-85 mm, d-150 mm, h=165 mm, 0 = 19%

The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench Illes in a vertical plane and a horizontal 160-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the 2-component of Mo be zero? Assume a-85 mm, d-150 mm, h=165 mm, 0 = 19%

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.119P: The hinge shown is the type used on the doors of some automobiles. If a torsion spring at F applies...

See similar textbooks

Similar questions

Find the internal force system acting on section 3 for the pin-connected frame.
The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The hinge shown is the type used on the doors of some automobiles. If a torsion spring at F applies the constant couple C0=20lbft to member ABF, calculate the force P required to hold the door open in the position shown.
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz-plane . Which of the following best approximates the magnitude of the moment of force Q about the y-axis?
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 16i - 13j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Determine the magnitude of the moment of P about the y-axis in Nm. Determine the magnitude of the moment of P about the z-axis in Nm. Determine the magnitude of the moment of P about the origin (point O) in Nm.
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly as shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz plane. 1. Which of the following quantities is/are zero? (Choices: A. Moment of P about the x-axis ; B. Moment of P about the y-axis ; C. Moment of P about the z-axis) 2. Which of the following best approximates the moment of force Q about point A? 3. Which of the following best approximates the equivalent force-couple set at point A of the applied forces P and Q? Note: F is the resultant force and Cis the resultant couple4. Considering the force diagram of member DE, which gives the complete set of reactions for the support at E? (Note difference of Force and couple reactions)
Determine the moment MAB produced by the force F shown in the figure which tends to rotate the bar about the axis AB.
Please reply as soon as possible, static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
Static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
2) The ABO vertical arm, whose weight of mass m is neglected in the figure, is kept in balance with a spherical joint to the wall with 3 cables. Calculate the reaction forces at point O and the force on all ropes. m=610 Please write the answer on a piece of paper
The figure shows a schematic diagram of a torsion -bar suspension for an automobile( the torsion bar appears in cross section at A). If the three forces and the couple C= 27000 Nmm are equivalent to a upward vertical force R= 1200 N acting at D, determine H and V.