The spool A rotates about its axis with an angular velocity of 30 rad/s, first in the sense of wo and second in the sense of wb- Simultaneously, the assembly rotates about the vertical axis with an angular velocity w₁ = 15 rad/s. Determine the magnitude w of total angular velocity of the spool and construct the body and space cones for the spool for each case. Assume 0 = 51°. 01 Wa A @b

The spool A rotates about its axis with an angular velocity of 30 rad/s, first in the sense of wo and second in the sense of wb- Simultaneously, the assembly rotates about the vertical axis with an angular velocity w₁ = 15 rad/s. Determine the magnitude w of total angular velocity of the spool and construct the body and space cones for the spool for each case. Assume 0 = 51°. 01 Wa A @b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The three forces act on the pipe assembly. If F1 = 80N and F2= 50 N replace this force system by an equivalent resultant force and couple moment acting at O. Express the results in Cartesian vector form.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
The Q-kg industrial door with mass center at G is being positioned for repair by insertion of the 5° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. The coefficients of static friction at both the top and bottom wedge surfaces are 0.66. Calculate the rightward force P' which would remove the wedge from under the door. Assume that corner A does not slip for your calculation of P'. Q = 402
Compute the value of EIy at 2.5 m from the left support.
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center ?, the spool has a larger radius ?=0,17 and an inner radius ?=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: ?? μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
7.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the horizontal force P to maintain equilibrium. Use unit weight of water 9.80 kN/m^3. Note: change 6 meters arc
Obtain the gage pressure at the center A of the pipe shown. Neglect the surface tension effects. Liquid 1, sg=1.5. Liquid 2, sg=3.2, h1=15cm; h2=30 cm; h3=75 cm.
H.w: drive a relation for Q of liquid flowing through half circular open conduit:
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)