Please answer, need asap. Thankyou bartleby! Problem 03The standard length of a tape is 100m having a weight of 2.5kg with the standard temperature of 20°Cand standard pull of 15kg. The young modulus of elasticity of the tape is 200GPA, cross sectional area is6.05mm? and the coefficient of linear expansion is 0.0000116/°C.3. Determine the normal tension of the tape in N.Note!The normal tension of a tape is the applied tension which will cause the effects of pull and sag to neutralizeeach other.

We havePull correction = sag correctionPn-Po×LAE=L×W224×Pn2Here,Pn= normal tensionPo= standard pull…

The standard length of a tape is 100m having a weight of 2.5kg with the standard temperature of 20°C and standard pull of 15kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 6.05mm² and the coefficient of linear expansion is 0.0000116/°C. 3. Determine the normal tension of the tape in N. Note! The normal tension of a tape is the applied tension which will cause the effects of pull and sag to neutralize each other.

The standard length of a tape is 100m having a weight of 2.5kg with the standard temperature of 20°C and standard pull of 15kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 6.05mm² and the coefficient of linear expansion is 0.0000116/°C. 3. Determine the normal tension of the tape in N. Note! The normal tension of a tape is the applied tension which will cause the effects of pull and sag to neutralize each other.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 100m tape is of standard length at a temperature of 20°C and a pull of 50N. It was used to measure a distance of 3768.92m. During measurement, the temperature reading was 29°C and the tape was supported at both end with an applied pull of 85N. The cross-sectional area of the tape is 2.8mm 2, the unit weight is 0.13N/m, themodulus of elasticity is 200GPa and the coefficient of linear expansion is 0.0000116/°C. Determine:a. the total temperature correctionb. the total pull correctionc. the total sag correctiond. the correct distance
The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 ̊C and standard pull of 5.5kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 2.8mm2 and the coefficient of linear expansion is 0.0000116/ ̊C. Determine the normal tension of the tape. Hint: The normal tension of a tape is the applied tension which will cause the effects of pull and sag to neutralize each other.
A 50m steel tape is used to measure the distance of the line and found to be 840.25m. During the measurement, the tape is supported at the ends and midpoint under a pull of 8kg and the observed mean temperature is 28°C. The tape is of standard length at 22°C and a tension of 12kg. The cross-section area of the tape is 0.030cm2. The coefficient of thermal expansion is 0.0000116°C and the modulus of elasticity of steel is 2.0x106 kg/cm2. The tape length is 1.0 kg. Determine the correct length of the tape.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of the external diameter of 3.6 cm and an internal diameter of 2 cm. The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis Solution: (i) The moment of inertia = Answer and unit for part 1 ii) The radius of curvature is Answer and unit for part 2 (iii) The maximum bending stress is Answer and unit for part 3 iv) The bending stress at the point 0.5 cm from the neutral axis is
the solid circular shaft rod has an original diameter of 20mm. when the load of 50kN is applied the shaft stretches 1.4mm and it has a Poisson's ratio of 0.25. Calculate the change in diameter of the shaft?Assume shaft is in the elastic region.
NOTE: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300 while the standard temp of the tape is 200 The cross sectional area of the tape is 0.05cm2. The coefficient of linear expansion is 0.000011610C and the modulus of elasticity of steel is given to be 2.0 x 106 kg/cm. The tape used here is a 50m steel tape. Determine the actual length of each lines
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
A civil engineer used a 30-m tape in measuring an inclined distance. The measured length of the slope was recorded to be 425.20m long the difference in elevation between the initial point and the end point was found to be 1.25 m. The 30-m tape is of standard length at a temperature of 10 deg. C and the tape was supported at both ends with an applied pull of 75 N. The cross-sectional are of the tape is 6.50 mm^2 and the modulus of elasticity is 200 GPa. The tape has a linear density of 0.075 kg/m, α = 0.0000116/dec. C. Neglect corrections due to sag. Determine the horizontal distance.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis (i) The moment of inertia in (mm^4)= ii) The radius of curvature in (mm) = (iii) The maximum bending stress in (N/mm^2)= iv) The bending stress at the point 0.6 cm from the neutral axis in (N/mm^2)=
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
A beam has a bending moment of 4 kN-m applied to a section with a hollow circular cross-section of external diameter 3.3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.8 cm from the neutral axis. (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.8 cm from the neutral axis is
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.