The state of plane stress at a point is represented by the element shown in Figure Q1. Construct a Mohr Circle to determine a) the principal plane and the principle stresses, b) the maximum in-plane shear stress and the associated average normal stress, and c) the state of stress at the point on another element oriented 25° clockwise from the position shown. d) Show the orientation of the element stresses on an appropriate sketch for a), b) and c) 60 MPa 30 MPa 45 MPa Figure Ql

The state of plane stress at a point is represented by the element shown in Figure Q1. Construct a Mohr Circle to determine a) the principal plane and the principle stresses, b) the maximum in-plane shear stress and the associated average normal stress, and c) the state of stress at the point on another element oriented 25° clockwise from the position shown. d) Show the orientation of the element stresses on an appropriate sketch for a), b) and c) 60 MPa 30 MPa 45 MPa Figure Ql

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements
An element in uniaxial stress is subjected totensile stresses σx = 57 MPa, as shown in the figure.Using Mohr’s circle, determine the following.(a) The stresses acting on an element oriented at anangle θ =-33° from the x axis (minus meansclockwise).(b) The maximum shear stresses and associatednormal stresses.Show all results on sketches of properly orientedelements.
S1) The figure shows the stress distribution in the rectangular cross section of a beam.According to this;(a) Write the expression for stress ?x, taking into account the directions of Fx, My and Mz.(b) Show that My is zero for symmetrical normal stress distribution.(c) Using the stress function ?x, find the axial force Fx acting on the rectangular cross sectionin width b and height h.(d) Obtain the equation of Mz bending moment.Hint: In this question, using the stress distribution in the figure, it is aimed to determine thecross-sectional effects of Fx, My ve Mz causing this stress distribution
For the stressed elements allocated to you, find the values and sketch the orientations: a) Maximum shear stress and the relative angle at which it occurs b) Principle normal stresses and the relative angle at which they occur c) The stresses at a 40° rotation from the initial element orientation i. using BOTH transformation equations AND Mohr’s circle
Represent the stress state on a 2-dimensional square element, given the Mohr circle below. (a) Determine the maximum shear stress. (b) Determine the maximum and minimum principal stresses. (c) Planes on which the greatest shear stress and principal stresses act are square other than the square element. Show the elements by drawing.
For the following data, using Mohr's circle of stress and trigonometry, (a) Find the principle stresses and show their sense in properly oriented element and (b) find the maximum (principle) shear stresses with the associated normal stresses and show the results on a properly oriented element.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
Figure shows a state of plane stress consists of normal stresses σx = 60 MPa and σy = -40MPa; and unknown shear stress, ?xy. The maximum principal stress was determined to be 104.34 MPa. Using Mohr’s circle, determine; the magnitude of the shear stress, the principal plane and the minimum principal stress. Then, sketch the element showing all stresses in its proper orientation, the maximum shear stress, associated normal stress and the orientation of the element. Then, sketch the element showing all stresses in its proper orientation, the stress components acting on the inclined plane AB. Then, sketch the element showing all stresses in its proper orientation.
Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
For the following steel beam, determine: a) State of stress at point A (shown on the element) b) Using Mohr's circle, determine the principal stress at point A and their orientation, and the maximum in-plane shear stress at point A.
The strain components for a point in a body subjected to plane strain are εx = 1170 με, εy = 290με and γxy = -228 μrad. Using Mohr’s circle, determine the principal strains (εp1 > εp2), the maximum inplane shear strain γip, and the absolute maximum shear strain γmax at the point. Show the angle θp (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch.