The state of stress at a point is shown on the element. Determine (a) the principal stress and (b) the maximum in-plane shear stress and average normal stress at the point. Specify the orientation of the element in each case. Sketch the results on each element. 60 MPa 30 MPa 45 MPa Problem 4. 0 Solve the problem 3.0 using Mohr's Circle.

The state of stress at a point is shown on the element. Determine (a) the principal stress and (b) the maximum in-plane shear stress and average normal stress at the point. Specify the orientation of the element in each case. Sketch the results on each element. 60 MPa 30 MPa 45 MPa Problem 4. 0 Solve the problem 3.0 using Mohr's Circle.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The diagram below shows Mohr’s circle for a point in a physicalobject that is subjected to plane stress.(a) Determine the stresses σ x, σ y, and τ xy, and show them on astress element.(b) Determine the principal stresses and the maximum in-planeshear stress acting at the point, and show these stresses on anappropriate sketch
Determine the equivalent state of stress on an element at the same point oriented 60° counterclockwise with respect to the element shown. Sketch the results on the element
Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with respect to the element shown. Sketch the results on the element.
For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle? (50 MPa, 25 MPa) (- 80 MPa, - 25 MPa) (- 80 MPa, 25 MPa) (50 MPa, - 25 MPa)
Given are the major and minor principal stresses at any point within a rock massσ1 = 50 MPa and σ3 = 20 MPaDetermine graphically the magnitude of the stress components acting on a plane that is inclined at an angle of 250to the major principal plane
Determine the average normal stress developed at points A, B, and C. The diameter ofeach segment is indicated in the Figure below.
Determine the principal stresses, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the element in each case.
The yield stress for a zirconium-magnesium alloy is sY = 15.3 ksi. If a machine part is made of this material and a critical point in the material is subjected to in-plane principal stresses s1 and s2 = -0.5s1, determine the magnitude of s1 that will cause yielding according to the maximum shear stress theory.
Determine the equivalent state of stress on an element which represents (a) the principal stresses, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shownand sketch the results on the element.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.