Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 1200 mm² A = 900 mm² P, Pa B C D mm-350 mm 500 mm -250 A

Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 1200 mm² A = 900 mm² P, Pa B C D mm-350 mm 500 mm -250 A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa a. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = ____ mm (2 decimal places) b. What is the condition of failure? = ____ (Balanced, Tension controlled, Compression controlled, Transition) c. Calculate the design moment strength of a typical interior beam. = ____ kN⋅m (whole number)
!! Show Complete & Detailed Solution w/ FBD !!The concrete post in the figure, is reinforced axially with four symmetrically placed steel bars, each ofcross-sectional area 750 mm2. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. A 2000-kN axial load is applied. Compute the:a. axial force in concrete;b. axial force in the steel bars;c. stress in the concrete;d. stress in the steel bars;e. deformation of the concrete post.
Help me how to design the REINFORCED CONCRETE BEAMS WITH IRREGULAR CROSS SECTION as shown infigure 1 using the following parameters:F’c = 3,500 Psi Fy=Grade 40 Stirrups = Φ10mmMu = 200 Kn-M All Concrete cover = 30mm Es=200,000 Mpa Find the following: AC area of compression concrete stress block in mm. Assume z = 0.85dEff a height of compression concrete stress block in mm. c distance from the neutral axis to outermost compression fiber in mm. z actual moment arm for Mu=ØTz in mm. As actual area of tension steel in sq.mm. N quantity of Ø20mm steel rebars ЄS Actual Strain of steel ЄY Yield Strain of steel Check if the beam is singly reinforced concrete in the designed then concludeCheck: ЄY < = > ЄS Draw the Working Drawings of the x-section.
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
Please answer in neat & complete solution. thanks Q: etermine the forces in all bars of the given set of trusses. Tabulate the answers per bar and their forces for every set of trusses. NOTE: Positive value (+) indicates tension and Negative value (-) indicates compression Where: (all units are in kN) P = 33 Q = 9 R = 2
Determine the maximum tensile stress σtand maximum compressive stress σc due to the load Pacting on the simple beam AB (see figure).(a) Data are P = 6.2 kN, L 5 3.2 m, d =1.25 m,b = 80 mm, t = 25 mm, h =120 mm, andh1 = 90 mm.(b) Find the value of d for which tensile andcompressive stresses are the largest. What arethese stresses?
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: Given: b(mm) = 250 h(mm) = 400 w(kN/m) = 15 Mb(kN-m) = 45 Using area moment method, determine the following: 1. Vertical reaction at A, RA. 2. Moment reaction at A, MA. 3. Flexural rigidity of the beam in N-mm^2 4. Rotation at B, in degrees. 5. Rotation at C. in degrees. 6. Deflection at B in mm. 7. Maximum deflection of the beam in mm. 8. If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN.
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.