The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the vertical displacement of its point of application is limited to 6 mm. Neglect the weights of the members. Aluminum A = 300 mm2 E = 70 GPa 2 m A В Steel A = 500 mm2 E = 200 GPa 2 m %3D 3 m 3 m C

The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the vertical displacement of its point of application is limited to 6 mm. Neglect the weights of the members. Aluminum A = 300 mm2 E = 70 GPa 2 m A В Steel A = 500 mm2 E = 200 GPa 2 m %3D 3 m 3 m C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the unknown tension T, which acts on the braked pulley. 275 N 1600 N 0.5 1.5 m- 1.8 m m 300 N A 1.25 m B 50° 0.6 m 650 N
The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 28 k N and x = 3.0 m. Write numerical value only and in 2 decimal places.
2) Load beam as in the figure a) Calculate the support reactions b) Draw Normal, Shear and Moment diagrams. (x: 6) (y: 5) (Units for x and y will be tons)
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the tension (lb) in the cable if the weight of the bar is 5,973 lb. Round off only on the final answer expressed in 3 decimal places .
Calculate for the axial force in kN at member GK of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
Determine the components of each force along the x and y axes shown inthe Figure.
1. Replace the three forces shown by a resultant force R through O and a couple.
# = poundsa) what is the shear force at 5' rt. of A? (in pounds, 2 decimal places)b) what is the bending moment at 5' rt. of A? (in pounds, 2 decimal places)
Calculate for the axial force in kN at member GC of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
The two vertical rods attached to the rigid bar are identical except for length. Before the weight P was attached, the bar was horizontal. Neglect the weight of the bar. Calculate the axial force in rod B in kips (4 decimal), if P=44 kips.
5 decimal placesss 1. A bar of 16-mm in diameter is only allowed to decrease at a maximum of 4.84% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 630 MPa, and the Poisson's ratio as 0.36.
Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa