The support member as shown in Figure 2 is designed for beam structure in one of the housing project. Member ABC is supported by a cable at A and pin at B. 300 N.m B 40 0.45 m 0.75 m 0.75 m Figure 2: Support member for beam structure а) Draw the free body diagram of support member shown in Figure 2.

The support member as shown in Figure 2 is designed for beam structure in one of the housing project. Member ABC is supported by a cable at A and pin at B. 300 N.m B 40 0.45 m 0.75 m 0.75 m Figure 2: Support member for beam structure а) Draw the free body diagram of support member shown in Figure 2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.5.2P: A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end...

See similar textbooks

Similar questions

A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end B, is subjected to a temperature differentia] with temperature T1on its upper surface and T2on its lower surface (see figure).
The deflection curve for a cantilever beam AB (sec figure) is given by v=q0x2120LEI(10L210L2x+5Lx2x3) Describe the load acting on the beam.
A simply supported beam 6 m in span is supported at supports A and B. The beam is acted upon a concentrated load of 100 KN at point C which is 2 m from support A. Also a udl of 20 KN/m is spread from point D to point B, where point D is at a distance of 1 m from point C Find S.F. and B.M. at all points and draw S.F.D. and B.M.D.
The accompanying figure shows the arrangement of beams and girders that are used to support a 5 in. reinforced concrete floor for a small industrial building. Design the beams and girders assuming that they are simply supported. Assume full lateral support of the compression flange and a live load of 80 psf. Concrete weight is 180 lb/ft3.t
Compute the initial deflection of the beam at midspan under service loads with the following specifications: f'c = 4000 psi, 36-inch height, depth of rebar assumed to be 3 inches less than the height, 16-inch width, 4 #9 bars (tension), Grade 60 rebar, 30' clear spans, service loads of: DL = 0.25k/ft, LL = 1.2k/ft. The DL does NOT include self-weight of the beam or of the precast concrete deck planks that have a weight of 60 PSF. The beam picks up a tributary width of 12 feet. Also, note that this beam is continuous and is the middle beam of 5 equal spans. Check the initial deflections against the ACI deflection requirements. Then calculate the long-term deflections and check those against the ACI requirements. For both situations, assume that finish materials will be attached to the beam. Last: Instead of performing a structural analysis to determine the maximum deflection in the beam, conservatively figure that the maximum deflection will be 60% of what it would have been for a…
Our University wants to construct a swimming pool inside the campus, for which they are in need of a diving board which must be one end fixed and other is free. That is to be made up of flexible composite material. The maximum allowable load at free end is 700 kN. The length of the cantilever beam is 1.6 m. The cross section of the beam is a hollow rectangular section. Outer rectangle of size 140 mm breadth and 110 mm depth with the overall wall thickness of 12 mm. Find the deflection at the free end and maximum slope in beam by neglecting self-weight of the diving board. Take E as 170 GPa.
A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its centre. The cross-section of the beam is 160 mm wide and 270 mm deep. If E for the beam is 70x109 N/m2, the deflection at the centre is
A cantilever beam weighing 100 lb isbolted rigidly to a wall at A. Find thereactions to keep the beam in equilibrium Please provide all written work
What is the force reaction at the fixed end of a 12-m cantilever beam due to a downward uniform load of 30 kN/m applied throughout the span? (Answer must be in kN.)
A simply supported beam of length 7m is carrying a uniformly distributed load of 1.25N/m for its entire length. What will be the total load on the beam? Select one: a. 8.75N b. 5.75N c. 87.5m d. 8.75m
The beam is subjected to the distributed loading as shown. Use E = 30,000 ksi, I = 394 in.4 , L = 23 ft, the max load distribution density at B w0 = 5 kip/ft, calculate the deflection at the middle of the beam: ___ in. Use apendix at end of the textbook and write down all the steps which lead to your anser. Pay attention to unit conversion, and calculate your answer to 1 decimal place
Read the question carefully and give me right solution according to the question.. Please answer all. Don't miss anything. Figure 5 shows a rigid horizontal beam ABCE which is supported by a pair of rectangular bars CD at C. The cross-sectional size of each of the rectangular bar is 37.5 × 12.5 mm. Modulus of elasticity of the bar is E=80 GPa. Vertical loads of 17.5 kN and 35 kN act at points B and E, respectively.Compute:i) Vertical displacement of point Bii) Vertical displacement of point EIf it is given that the allowable displacement of point C is 1 mm, determine the minimum thickness of rectangular bar CD required. The width of the rectangular bar should be kept unchanged at 37.5 mm.