The system shown in Figure 1 is used for modulation an audio signal M(t). The output y(t) is the modulated version of the input m(t). mtt) LPF Fc= 15KHZ. Figure 1 2 cos(3000 nt) a. If the power of the message is 10 kW, what is the power of y(t)? b. Draw the spectrum of the modulated signal, y(t)? c. Suggest a method for detection m(t) from y(t) in details?

The system shown in Figure 1 is used for modulation an audio signal M(t). The output y(t) is the modulated version of the input m(t). mtt) LPF Fc= 15KHZ. Figure 1 2 cos(3000 nt) a. If the power of the message is 10 kW, what is the power of y(t)? b. Draw the spectrum of the modulated signal, y(t)? c. Suggest a method for detection m(t) from y(t) in details?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 57 Ohms dummy load is used to test a certain FM station. Suppose the measured power is 19.62 W, what is the voltage level (in Vrms) of the second sideband if a frequency of 5 kHz test tone is used and a 10 kHz frequency deviation? The modulation index is 2.
Q4. Step 2.2 Plot the following equations: m(t) = 2cos(2π*1.2kHz*t) c(t) = 5cos(2π*10.5kHz*t) Question 4. Having made the changes, select the correct statement regarding your observation. The signal, s(t), faithfully represents the original message wave m(t) The receiver will be unable to demodulate the modulated carrier wave shown in the upper left plot The AM modulated carrier shows significant signal distortion a and b
1.Select the correct statement(s) regarding the FM Index. a. Δf represents the amount of frequency that the carrier wave can change in order to represent the baseband (information/message) signal b. β=(KvcoAm)/fm is a ratio that has no units c. the larger the FM index, the greater the frequency bandwidth d. all statements are correct 2. Select the correct statement(s) regarding viewing an information signal in time and/or frequency domains. a. only the viewing a signal in the time domain is important since the transmission/carrier frequency is an assigned parameter b. observing the signal in the time domain does not give you information regarding the capacity or bandwidth of the signal c. a signal observed in the frequency domain provides information regarding signal amplitude and the periodic or non-periodic nature of the signal d. all of the above are correct 3. Select the…
A message signal consisting of 2 tone signals at 100 Hz and 600 Hz frequencies with amplitudes of 1V and 3V, respectively, will be transmitted by modulating with DSB. The frequency of the carrier signal is 2 kHz. Which of the following statements are true? I. The bandwidth of the modulated signal is 1.2 kHz. ii. The dissipated power of the message signal on a 1ohm resistor (normalized) is 4.5 Watts. iii. The frequency components of the modulated signal are at 1.7 kHz, 1.9 kHz, 2.1 kHz, 2.3 kHz. a) All of above b) only i c) i and iii d) only iii
For a FM system, if the expression of the modulated wave is x(t)=5cos(2000t+5.5sin100t) V, then what will be the transmitted power?
FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. What is the bandwidth of the FM modulated signal based on Carson's Rule? a)120Hz b)240Hz c)40Hz d)80Hz
If a carrier signal vc(t) = 9 cos(2 pi 3000t) Volts is modulated by a sine wave vm(t) =7 cos(2 pi 440t) V, what is the percentage modulation of the resulting AM signal? 83% 77% 70% none of the given answers
a) The output signal from an AM modulator is u(t) = 5 cos(1800πt) + 20 cos(2000πt) + 5cos(2200πt).(1) Determine the message signal m(t) and the carrier c(t). (Hint: Look at the spectrum of u(t).(2) Determine the modulation index. (3) Determine the ratio of the power in the sidebands to thepower in the carrier.
The output signal from a conventional AM modulator isu(t) = 12 cos(2pi 8800 t) + 12 cos(2pi 7200 t) + 24 cos(2pi 8000 t)1. Determine the modulated signal m(t) and the carrier c(t).2. Determine the modulation index.3. Determine and sketch the spectrum of the signal u(t).4. Determine the power in the sidebands and the power of the carrier.
P2/ an FM transmitter operates with a total power of 10 w, a frequency deviation of 5 KHz and a modulation index of 2. If the receiver has a sufficient bandwidth for Include the carrier and the first two pairs of side bands, what is the percentage of Total power of the signal you receive?
An FM signal is described by s(t) = 100cos(2pi * 10 ^ 6 * t + 0.02sin(1000pi * t)) (a) Determine the instantaneous frequency f j (t);(b) Determine the frequency deviation 4 and the modulation index beta / (0) What is the approximate bandwidth of x(t) ; (d) In this a narrowband or wideband FM signal? Why?
1. An FM transmitter is determined to have a transmitter sensitivity of 728.832Hz/V. Determine the percent modulation of the system if the modulating signal is determined to be Vm(t)=25sin(12566.3706t)Vm(t)=25sin⁡(12566.3706t). 2. The SNRo of a receiver is determined to be 35.937dB. Determine the SNRi in dB, if the modulation index is kept at 2 and the modulating signal is determined to have a peak voltage of 12.452. It is also noted that the system's sensitivity to changes in frequency is 200.718Hz/V. This modulator is using the maximum frequency deviation.