Positive rating for free body diagram and explanation The system shown is at rest. Piston A (mA==2.25 slug) hasa diameter of 4.50 in and supports a crate which has aweight W = 1690 lb. An unknown fluid fills the spacebetween Pistons A and B. Piston B (mB = 0.150 slug) hasa diameter of d = 0.690 in. Atmospheric pressure is 14.7psi. What is the pressure in the fluid just under Piston A?What is the magnitude of the force F? CratePistonA4.50 influidF→d←Piston B

Answered: Image /qna-images/answer/5a4adf4d-083e-4b1a-b80f-681c95e317db.jpg

The system shown is at rest. Piston A (mA = 2.25 slug) has a diameter of 4.50 in and supports a crate which has a weight W = between Pistons A and B. Piston B (mB = 0.150 slug) has 1690 lb. An unknown fluid fills the space a diameter of d = 0.690 in. Atmospheric pressure is 14.7 psi. What is the pressure in the fluid just under Piston A? What is the magnitude of the force F?

The system shown is at rest. Piston A (mA = 2.25 slug) has a diameter of 4.50 in and supports a crate which has a weight W = between Pistons A and B. Piston B (mB = 0.150 slug) has 1690 lb. An unknown fluid fills the space a diameter of d = 0.690 in. Atmospheric pressure is 14.7 psi. What is the pressure in the fluid just under Piston A? What is the magnitude of the force F?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subejct: Hydraulics/Fluid Mechanics Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage. Determine the value of H in m if the pressure at A is 142 kPa.
8. A pump takes water from an 8 inch suction pipe and delivers it to a ó inch pipe in which the velocity is 8 feet per second. At a point along the suc tion pipe, a pressure of -6 psi is observed while a pressure of 60 psi is observed along the discharge pipe. 15 feet higher than the previous point. What horsepower must be supplied to the pump of efficiency 80 percent to maintain the system.
Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 ℃。The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is , D=20 cm, the rate of flow is 0.06 m3/s, . Please calculate the pressure in the pipe.
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
Oil (SG=0.82) entering a pump through an 180mm diameter pipe at 35kPa has a flow rate of 0.07 m^3/s. It leaves the pump through a 120mm diameter pipe at 120 kPa. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (746 watts = 1 HP). Illustrate the problem and show your complete solution.
A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp.gr. = 0.80 and 6 m. of water. A horizontal circular orifice 75 mm in diameter is situated at the bottom. Coefficient of velocity is 0.98 and coefficient of contraction is 0.61. Neglecting velocity of approach. a. Determine the velocity of the jet issuing from the orifice at the instant the surface of the liquid in the tank is 6.5 m. above the orifice. b. Determine the discharge in kg/sec. through the orifice at the instant the surface of the liquid is 5.5 m. above the orifice. c. Compute the total time to empty the container.
plzzzz help meee right nowww plzzz what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=7.5, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle
Figure 1 represent two large tanks with an orifice in the dividing partition. The orifice has a diameter of 50mm and is rounded so that Cc=1.0 and Cv =0.97.Pressure pA and pB are atmospheric. The liquid is oil with h=4.87m. determine the discharge.
From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a certain rate which produces power in the jet equal to 10 hp. Diameter of orifice is 125mm with Cv = 0.95 and Cc = 0.68. Find the pressure at B.
A pumping system operates at full load transferring oil (Sp= 0.87) from a point located 150 meters above sea level to another located at 1250 meters above sea level. The pressure at the suction is 150 psi and at the discharge 258.6 psi, calculate the fluid flow rate handled by the system, knowing that the diameter ratio between suction and discharge is 3 (Ds/Dd); Dd= 20 cm.
calculate a- The volume flow rate from the nozzle b- The pressure at A and B.
The fluid in the figure is water, with the surface 10m above the datum. The pipe is 15cm in diameter and the head losses are as follows: from 1 to 2, 0m; from 2 to 3, 0.60m; from 3 to 4, 2m; and from 4 to 5, 0.30m. 1.Determine the velocity of flow in the pipe in m/s. 2.Determine the discharge Q in m^3/s. 3.How many centimeters above the center of the pipe will water stand in piezometer tube 3? 4.How many centimeters above the center of the pipe will water stand in piezometer tube 4?