The tank is filled with air at 20°C and 139 kPa in stationary condition. Air is leaving the tank with floW nozzle under steady-state condition. The flow is under isentropic and subsonic condition. The nozzle exit area is 18,59 cm?. After leaving from the nozzle, air strikes a vertical plate. Define the force [N] required to hold the plate stationary. (Note: Assume Pe=1 atm, kair=1.4, Rair=287 J/kg.K)

The tank is filled with air at 20°C and 139 kPa in stationary condition. Air is leaving the tank with floW nozzle under steady-state condition. The flow is under isentropic and subsonic condition. The nozzle exit area is 18,59 cm?. After leaving from the nozzle, air strikes a vertical plate. Define the force [N] required to hold the plate stationary. (Note: Assume Pe=1 atm, kair=1.4, Rair=287 J/kg.K)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.68P

See similar textbooks

Similar questions

An aircraft is flying at supersonic speed. At a component of an aircraft where the flow is perpendicular (normalshock), the density ratio is 5. Solve for: a.Mach Number Downstream b. Pressure Ratio c. Temperature Ratio d. Mach Number upstream
An aircraft is flying at supersonic speed. At a component of an aircraft where the flow is perpendicular, the density ratio is 5. Solve for: a.Mach Number Downstream b. Pressure Ratio c. Temperature Ratio d. Mach Number upstream
An aircraft is designed to cruise at Mach number Ma = 1.1 at 12,000 m where the atmospheric temperature is 236.15 K. Determine the stagnation temperature on the leading edge of the wing.
Consider a typical air flow around a cruising jetliner at 10km altitude. The speed is now 810 km/h, while the ambient conditions are 0.414 kg/m³ , 0.261 atm and -50°C. At the stagnation point, the temperature rises over by 25°C, while the density and pressure changes by more than 30% and 45 % respectively. Classify the following situations as compressible/incompressible flow
A subsonic airplane is flying at a 5000-m altitude where the atmospheric conditions are 54 kPa and 256 K. A Pitot static probe measures the difference between the static and stagnation pressures to be 16 kPa. Calculate the speed of the airplane and the flight Mach number.
Consider a hypersonic vehicle with a spherical nose flying at Mach 20at a standard altitude of 150,000 ft, where the ambient temperature andpressure are 500◦R and 3.06 lb/ft2, respectively. At the point on thesurface of the nose located 20◦ away from the stagnation point, estimatethe: (a) pressure, (b) temperature, (c) Mach number, and (d) velocity ofthe flow.
Air enters a diffuser with a velocity of 200m/s. Determine the speed of sound Mach number at the diffuser inlet at 30°C
Calculate the ratio of kinetic energy to internal energy at a point in an airflow where the Mach number is: (a) M = 2, and (b) M = 20.
The Mach number behind a normal shock wave is 0.4752. What is the Mach number in front of the wave? What are the density, pressure, and temperature ratios across the shock?
Consider air entering a heated duct at p1 = 1 atm and T1 = 288 K. Ignore the effect of friction. Calculate the amount of heat per unit mass (in joules per kilogram) necessary to choke the flow at the exit of the duct for an inlet Mach number of M1 = 2.2.
Calculate the Mach number of the exit if the diverging duct has an inlet area and velocity of air of 0.5m^2 and 60 m/s respectively. The exit area is 8 times the inlet, and the temperature on the exit is standard atmospheric value. Your answer
Air at Ma1 = 2.0 and p1 = 100 kPa undergoes an isentropicexpansion to a downstream pressure of 50 kPa. What is thedesired turn angle in degrees?